manualshive.com logo in svg

YASKAWA CANopen SI-S3/V, Руководство по установке

Поделиться
Скачать
YASKAWA CANopen SI-S3/V Скачать руководство пользователя страница 5

1  Preface and Safety

YASKAWA

 TOBP C730600 24A V1000 Option CANopen Installation Manual

 5

◆

Applicable Documentation

The following manuals are available for SI-S3/V CANopen Option unit:

For the drive setup, refer to one of the documentation listed below.

◆

Terms

Note:

Indicates a supplement or precaution that does not cause drive damage.

 

Option Unit

V1000 Option CANopen Installation Manual (this book)

Manual No. : TOBP C730600 24

Read this manual first.
The installation manual is packaged with the CANopen Option and contains a basic 
overview of wiring, settings, functions, and fault diagnoses.

V1000 Option CANopen Technical Manual

Manual No. : SIEP C730600 24

The technical manual contains detailed information and command registers.
To obtain the technical manual access these sites:
Europe: http://www.yaskawa.eu.com
Japan: https://www.e-mechatronics.com
Other areas: contact a Yaskawa representative.

Yaskawa Drive

V1000 Series AC Drive Technical Manual

Manual No. : SIEP C710606 16

This manual describes installation, wiring, operation procedures, functions, 
troubleshooting, maintenance, and inspections to perform before operation.
To obtain instruction manuals for Yaskawa products access these sites:
Europe: http//www.yaskawa.eu.com
Japan: https//www.e-mechatronics.com
Other areas: contact a Yaskawa representative

V1000 Series AC Drive Quick Start Guide

This guide is packaged together with the product. It contains basic information 
required to install and wire the drive. This guide provides basic programming and 
simple set-up and adjustment.

Drive:

Yaskawa AC Drive -V1000 Series

CANopen Option:

Yaskawa AC Drive -SI-S3/V CANopen option unit for the Yaskawa V1000 
drive

STOP

(Hz)

(Hz)
(A)
(V)










V1000

๟ᵄᢙᜰ઎
ᱜォㅒォㆬᛯ
಴ജ๟ᵄᢙ
಴ജ㔚ᵹ
಴ജ㔚࿶
ࡕ࠾࠲
ࡌ࡝ࡈࠔࠗ
࠮࠶࠻ࠕ࠶ࡊ
ࡄ࡜ࡔ࡯࠲⸳ቯ
ࠝ࡯࠻࠴ࡘ࡯࠾ࡦࠣ

ᝪ߃ઃߌޔㆇォߩ೨ߦߪᔅߕขᛒ⺑᣿ᦠࠍ⺒߻ߎߣޕ
ㅢ㔚ਛ߅ࠃ߮㔚Ḯㆤᢿᓟ

5

ಽએౝߪࡈࡠࡦ࠻ࠞࡃ࡯ࠍ

ᄖߐߥ޿ߎߣޕ

400V

⚖ࠗࡦࡃ࡯࠲ߩ႐วߪޔ㔚Ḯߩਛᕈὐ߇ធ࿾

ߐࠇߡ޿ࠆߎߣࠍ⏕⹺ߔࠆߎߣޕ㧔ޓޓኻᔕ㧕

ߌ߇㧚ᗵ㔚ߩ߅ߘࠇ߇޽ࠅ߹ߔޕ

ෂޓ㒾

Содержание CANopen SI-S3/V








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды