manualshive.com logo in svg

YASKAWA CANopen SI-S3/V, Руководство по установке

Поделиться
Скачать
YASKAWA CANopen SI-S3/V Скачать руководство пользователя страница 26

26

YASKAWA

 

TOBP C730600 24A V1000 Option CANopen Installation Manual

6  CANopen Parameters

6

CANopen Parameters

Confirm the proper setting of all parameters in Table 5 before starting network 
communications.

Table 5  Parameter Settings

No.

Name

Description

Default

b1-01

<1> <2>

Frequency Reference 
Selection

 

Selects the frequency reference input source
0: Operator - Digital preset speed d1-01 to d1-17
1: Terminals - Analog input terminal A1 or A2
2: MEMOBUS communications 
3: Option PCB
4: Pulse Input (Terminal RP)

1

b1-02

<1> <2>

Run Command Selection

 

Selects the run command input source
0: Digital Operator - RUN and STOP keys
1: Digital input terminals S1 to S7 
2: MEMOBUS communications 
3: Option PCB

1

E2-04 

<3>

Motor 1 Motor Poles

Set the number of motor poles described on the 
motor nameplate.

4 poles

E4-04

 <3>

Motor 2 Motor Poles

Sets the number of poles of motor 2. 

4 poles

E5-04

 <3>

PM Motor Pole Number

Sets the number of motor poles for PM motors.

<4>

F6-01

Operation Selection after 
Communications Error

Determines drive response when a bUS error is 
detected during communications with the 
CANopen Option
0: Ramp to Stop 
1: Coast to Stop
2: Fast-Stop
3: Alarm Only

1

F6-02

External Fault Detection 
Conditions (EF0)

Sets the condition for external fault detection 
(EF0)
0: Always detected.
1: Detected only during operation.

0

F6-03

Stopping Method for 
External Fault from 
Communication Option 
Board

Determines drive response for external fault input 
(EF0) detection during CANopen communication
0: Ramp to Stop 
1: Coast to Stop
2: Fast-Stop
3: Alarm Only 

<5>

1

F6-04

bUS Error Detection Delay 
Time

Set the maximum time the drive should wait for a 
communication error to occur (bUS).
Range 0.00 to 5.00 s

0.05 s

F6-35 

<6>

Node Address

0 to 127

0

（

1012 or later

）

<7>

Содержание CANopen SI-S3/V








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды