manualshive.com logo in svg

YASKAWA CANopen SI-S3/V, Руководство по установке

Поделиться
Скачать
YASKAWA CANopen SI-S3/V Скачать руководство пользователя страница 21

5  Installation Procedure

YASKAWA

 TOBP C730600 24A V1000 Option CANopen Installation Manual

 21

◆

Installing the Option Unit

Remove the front cover of the drive before installing the CANopen Option. Follow 

the directions below for proper installation.

1. Switch off the power supply to the drive.

DANGER!

Electrical Shock Hazard

 - Do not connect or disconnect wiring while the power is 

on. Failure to comply will result in death or serious injury. Before installing the CANopen 

Option, disconnect all power to the drive. The internal capacitor remains charged even after 

the power supply is turned off. The charge indicator LED will extinguish when the DC bus 

voltage is below 50 Vdc. To prevent electric shock, wait at least five minutes after all indicators 

are off and measure the DC bus voltage level to confirm safe level.

2. Remove the front cover. The original drive front cover may be discarded because 

it will be replaced by the CANopen Option cover in step 7.

Figure 7  Remove Front Cover

3. Remove the bottom cover and connect the CANopen Option ground cable to the 

ground terminal.

Figure 8  Connect Ground Cable

ground terminal

ground cable

bottom cover

Содержание CANopen SI-S3/V








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды