29
TROUBLESHOOTING
PROBLEM
CAUSE
CORRECTION
Engine continues to
run when operator
leaves seat with
attachment clutch
engaged
1. Faulty operator-safety presence control
system.
1. Check wiring, switches and connections. If not
corrected, contact an authorized service center/
department.
CAUTION: DO NOT operate machine until
problem is corrected.
Poor cut - uneven
1. Worn, bent or loose blade.
1. Replace blade. Tighten blade bolt.
2. Mower deck not level.
2. Level mower deck.
3. Buildup of grass, leaves, or trash under mower.
3. Clean underside of mower housing.
4. Bent blade mandrel.
4. Replace blade mandrel.
5. Clogged mower deck vent holes from buildup
of grass, leaves, and trash around mandrels.
5. Clean around mandrels to open vent holes.
Mower blades will
not rotate
1. Obstruction in clutch mechanism.
1. Remove obstruction.
2. Worn/damaged mower drive belt.
2. Replace mower drive belt.
3. Frozen idler pulley.
3. Replace idler pulley.
4. Frozen blade mandrel.
4. Replace blade mandrel.
Poor grass
discharge
1. Engine speed too slow.
1. Place throttle control in “FAST” position.
2. Travel speed too fast.
2. Shift to slower speed.
3. Wet grass.
3. Allow grass to dry before mowing.
4. Mower deck not level.
4. Level mower deck.
5. Low/uneven tire air pressure.
5. Check tires for proper air pressure.
6. Worn, bent or loose blade.
6. Replace blade. Tighten blade bolt.
7. Buildup of grass, leaves and trash under
mower.
7. Clean underside of mower housing.
8. Mower drive belt worn.
8. Replace mower drive belt.
9. Blades improperly installed.
9. Reinstall blades sharp edge down.
10. Improper blades used.
10. Replace with blades listed in parts manual.
11. Clogged mower deck vent holes from buildup
of grass, leaves, and trash around mandrels.
11. Clean around mandrels to open vent holes.
Headlight(s) not
working
(if so equipped)
1. Switch is “OFF”.
1. Turn switch “ON”.
2. Bulb(s) or lamp(s) burned out.
2. Replace bulb(s) or lamp(s).
3. Faulty light switch.
3. Check/replace light switch.
4. Loose or damaged wiring.
4. Check wiring and connections.
5. Blown fuse.
5. Replace fuse.
Battery will not
charge
1. Bad battery cell(s).
1. Replace battery.
2. Poor cable connections.
2. Check/clean all connections.
3. Faulty regulator (if so equipped).
3. Replace regulator.
4. Faulty alternator.
4. Replace alternator.
Loss of drive
1. Debris on steering plate (if equipped).
1. See "CLEANING" in the Maintenance section.
2. Motion drive belt worn, damaged, or broken.
2. Replace motion drive belt.
3. Axle key missing.
3. Install axle key at rear wheel. See "TO REMOVE
WHEEL" in the Service and Adjustments section.
Engine "backfires”
when turning
engine “OFF”
1. Engine throttle control not set between
half and full speed (fast) position before
stopping engine.
1. Move throttle control between half and full speed
(fast) position before stopping engine.
Engine dies when
tractor is shifted
into reverse
1. Reverse operation system (ROS) is not
"ON" while mower or other attachment is
engaged.
1. Turn ignition key to ROS "ON" position. See
Operation section.
Содержание YP18KH38
Страница 32: ...05 20 14 BD Printed in the U S A...
