background image

10

you to slip and fall. New grass, thick grass, or wet grass 
may require a narrower cut.

For a healthier lawn, never cut off more than one-third 
of the total length of the grass. Your lawn should be cut 
in the fall as long as there is growth. This mower is 
designed to be operated at full throttle to give you the 
best cut and do the most effective job of mowing or 
mulching.

WARNING: If you strike a foreign object,
stop the engine. Remove wire from the
spark plug, thoroughly inspect the mower
for any damage, and repair the damage
before restarting and operating the
mower. Extensive vibration of the mower
during operation is an indication of
damage. The unit should be promptly
inspected and repaired.

Mulching

For effective mulching, do not cut wet grass because it 
tends to stick to the underside of the deck, preventing 
proper mulching of grass clippings. New or thick grass 
may require a narrower cut. The ground speed should 
be adjusted to the condition of the lawn. If mowing has 
been delayed and the grass has been allowed to grow 
in excess of 4”, mulching is not recommended. Mow 
using the grass bag to reduce the grass height to 3 1/4” 
maximum before mulching.

Attaching The Grass Bag  

Remove three wing nuts holding the mulching 
baffle or side discharge chute in place and remove 
from unit.

Replace with grass bag adapter, while making   
sure the front lip of adapter goes under the  edge of 
the deck. Secure with wing nuts previously 
removed.  See Figure 7.

Figure 7

Lift chute door on the grass bag adapter and slide 
grass bag onto the adapter. See Figure 8.

NOTE: The chute door has been designed to move the
starter rope out of the way of the bag when the chute
door is opened.

Figure 8  

Attaching Side Discharge Chute 

Remove mulching baffle or grass bag adapter from 
unit by disconnecting wing nuts. 

Attach side discharge chute to unit and secure with 
the three wing nuts. See Figure 9.

Figure 9     

Emptying the Grass Bag

While holding the grass bag by both the rear handle 
and the lower handle, lift the grass bag straight up 
off the adapter. The chute door will move the rope 
out of the way of the bag.

Continue to hold the lower handle and raise the 
rear of the grass bag up toward your chest. The 
grass bag will open and the grass clippings will 
disperse.

When replacing the grass bag, be sure the  top of 
the bag rests on the wire support between the 
handles.

Grass Bag
Adapter

Wing
Nuts

Grass
Bag

Chute
Door

Side Discharge
Chute

Содержание 979 Series

























Отзывы: