background image

11

Throttle Control: 

The throttle control lever adjusts the 

engine speed and stops the engine. With the throttle 
control lever pushed completely forward, the carburetor 
is in START position. Pulling the throttle control back 
slightly adjusts the engine speed to FAST. Pulling the 
throttle back further reduces the engine speed to 
SLOW. Pull the throttle completely back to stop the 
engine.
Use maximum engine speed for deep tilling. Move the 
throttle control to SLOW when transporting the tiller.

Transporting The Tiller

To transport the tiller to or from the garden, pivot the 
depth stake forward, out of the way.  See Figure 12. 
With the throttle control in SLOW position, the unit will 
walk freely on top of the lawn. If the operator does not 
allow the tiller to move freely, the unit will start to till the 
surface.

Cultivating

For cultivating, a two to three inch depth is desirable. 
Setting the wheels and depth stake so that the wheels 
are about two inches above the ground while the tiller is 
resting on the tines and depth stake will allow the 
machine to work at cultivating depth. The throttle 
should be set to control forward movement to a slow 
walking speed. With the outer tines installed, the 
working width of the machine is 22 or 24 inches. For 
cultivation, this may be reduced to 13 inches by 
removing the outer tines. Refer to Tine Width 
Adjustment in Adjustment section. When laying out 
plant rows, be sure to allow enough width to permit 
cultivation between the rows. In growing corn or similar 
crops, check-row planting will permit cross cultivation 
and practically eliminate hand hoeing.

 

 

Figure 14

The tiller has many uses other than tilling and 
cultivating a garden. One of these is the preparation of 
lawn area for seeding. The tiller will prepare a deep 
seed bed which will be free of hard untilled spots, 
allowing a better stand of grass to grow. The tiller is 
very useful for loosening hard soil for excavation with a 
shovel. No tedious hand pickwork will be necessary. 
Your tiller may be used for mixing compost in the pile, 
or for mixing it with the soil in your garden. This should 
be done after the soil has been broken to the full 
working depth. The compost should be worked in to a 
depth of six to seven inches. This may be done by 
working the length of the garden, and then by making 
separate passes across its width. The addition of 
decayed organic matter will substantially increase the 
fertility of your garden. For proper decaying action, 
fertilizer should be applied and worked in with the 
mulch materials. Breaking up leaves and straw and 
mixing it with several inches of soil causes the soil to 
hold moisture longer and allows proper aeration of the 
plant root system. This also retards the growth of 
weeds.

The U.S. Department of Agriculture and various state 
and local agencies offer published booklets and expert 
advice on all phases of gardening. They should be 
consulted regarding soil information, planting dates, 
and the most satisfactory varieties of crop for your 
particular area.

Содержание 390 Series

























Отзывы: