background image

6

Figure 3 

Attaching Clutch Control Cable(s)

Forward Cable

Attach the end of the forward cable to the bracket 
underneath the handle assembly as follows. (On model 
390, the forward clutch cable is the cable which is 

attached closer to the rear of the tiller).

Loosen the hex nut on the threaded rod near the 
end of the cable, and move it up the rod as far as it 
will go.

Unthread the rod from the rest of the cable. Hook 
the “Z” end of the rod into the bracket underneath 
the handle assembly from the right hand side. See 
Figure 4.

Thread the rod back into the cable until the cable is 
straight. Do not tighten it enough to put any tension 
on the spring.

Thread the hex nut down against the end of cable. 
Use a pair of pliers and a wrench to lock the nut 
against the rod.

NOTE: 

Do not overtighten control cable. Too much

tension may cause it to break when engaged.

Figure 4

Reverse Cable 

(Model 390 Only)

The reverse clutch cable is the cable which is attached 
closer to the front of the tiller. Attach the end of the 
reverse cable to the reverse tine drive clutch lever, 
above the handle assembly, in the same manner as 
you attached the forward cable. See Figure 5.

Figure 5

Hex

Lock Nut

Spark

Plug

Handle

Brace

Briggs and Stratton Standard Engine

 

Tecumseh Engine

Handle

Brace

Hex

Lock Nut

Spark

Plug

Handle 

Handle

Brace

Handle

Hex Bolt

Cupped

Washer

Frame

Half

Welded
Bracket

Crank

Fuel 

Shut-off

Valve

Briggs and Stratton Intek Engine

 

“Z” End

Hooked In

 

Bracket

Threaded

Rod

Hex Nut

Cable

Models 340 thru 345

Reverse

 Cable

Hex Nut

Threaded

Rod

Reverse Tine

 

Engagement Handle

“Z” End

Hooked In

 

Bracket

Model 390

Содержание 390 Series

























Отзывы: