Yard force YF7302 Скачать руководство пользователя страница 23

Страница: 23 / 30

Troubleshooting

pROBLEM

pOSSiBLE CAUSE(S)

SOLUTiON(S)

Engine difficult to start

1. Out of fuel

2. Start lever is not

compressed

3. Choke in “Run /

Warm Start” position

4. Spark plug wire

disconnected

5. fouled spark plug

6. Dirty Carburetor

7. Clogged air filter

8. Clogged fuel filter

9. Contaminated fuel

1. Add fresh fuel

2. Pull start lever against handle

3. Rotate Choke lever to “Choke

/ Cold Start” position

4. Attach spark plug wire to

spark plug

5. Remove spark plug. Inspect.

Replace if necessary

6. Take unit to an authorized

service center for Carburetor

cleaning

7. Remove and clean air filter

8. Remove fuel filter. Inspect.

Replace if necessary

9. Drain fuel

Engine Problems

Engine smokes excessively

Engine runs very “rough”

Engine runs erratically

Engine cannot maintain full

speed

1. No Engine Oil

2. Engine oil not at

proper level

3. fouled spark plug

4. Clogged air filter

5. Clogged fuel filter

6. Contaminated fuel

7. Carburetor out of

adjustment

8. Choke in “Choke /

Cold Start” position

1. Add engine oil

2. Check engine oil. Add or

drain engine oil if necessary

3. Remove spark plug. Inspect.

Replace if necessary

4. Remove and clean air filter

5. Remove fuel filter. Inspect.

Replace if necessary

6. Drain fuel tank. Clean fuel

tank. fill with fresh fuel

7. Take unit to an authorized

service center for Carburetor

adjustment

8. Rotate Choke to “Run / Warm

Start” position

Excessive vibration / noise

1. loose parts

2. Engine problems

(above)

1. Tighten all fasteners

2. Refer to engine solutions

(above)

blade will not rotate

1. Debris interfering with

blade

2. blade loose

3. belt loose

1. Remove debris from around

blade

2. Tighten blade nuts

3. Replace belt

Engine will not stop

flameout wire terminals

disconnected

Connect handle and engine

flameout wire

terminals

blade will not cut properly

Damaged or worn blade Replace blade

frequent engine stalling

1. Excessive edging

speed / depth

2. Engine problems

(above)

1. Edge at a moderate pace.

Make multiple passes.

2. Refer to engine solutions

(above)

Содержание YF7302































Результаты поиска

Содержание YF7302

Отзывы:

Бренды по названию

Популярные бренды

Yard force YF7302, Руководство оператора

Результаты поиска

Содержание YF7302

Отзывы:

Бренды по названию

Популярные бренды