Yard force YF7302 Скачать руководство пользователя страница 21

Страница: 21 / 30

4. Remove the blade.

5. Replace with new blade from the manufacturer by reversing the above steps.

Note: Tighten the blade locknut to 35-45 foot-pounds (47-61 N-m)

How to Clean the Air Filter

A dirty air filter will restrict air intake. Regular maintenance of air cleaner will help

improve engine performance and reduce emissions.

WARNiNG!

Never clean air filter with gasoline or an easy ignited solvent because it

may cause explosion.

NOTE: Refer to figure 12 when following the steps below:

1. Remove the air filter cover bolts.

2. Remove the air filter cover.

3. Carefully remove air filter element to

prevent dirt from falling into carburetor.

4. Clean all parts. Wash the air filter element

in a nonflammable or high burning point

solvent, and allow to dry thoroughly; dip the

filter element in clean oil, and squeeze out

all excess oil.

5. Reinstall the air filter element.

6. Replace air filter cover and tighten cover

bolts.

How to Check the Spark plug

Spark plug Model: Torch E7RTC

WARNiNG!

Only use the recommended spark

plug or a spark plug with the same

temperature range. using an improper

spark plug, an incorrect spark plug

gap, or a dirty/fouled spark plug can

reduce engine performance and cause

damage.

1. Stop engine and allow it to cool.

2. Remove spark plug wire from spark plug.

3. use the spark plug wrench and rod

(included with edger) to remove the spark

plug. (See figure 13)

Spark Plug

Wrench

and Rod

figure 13

0.024 - 0.028 in

0.6 - 0.7 mm

figure 14

Air filter Cover

Air filter Element

Cover bolt

figure 12

Содержание YF7302































Результаты поиска

Содержание YF7302

Отзывы:

Бренды по названию

Популярные бренды

Yard force YF7302, Руководство оператора

Результаты поиска

Содержание YF7302

Отзывы:

Бренды по названию

Популярные бренды