24
25
OPERATION
WARNING:
Dress properly to reduce the risk of injury when operating this tool. Do not
wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy duty, long
trousers, boots and gloves. Do not wear short trousers, sandals or go barefoot.
Before operating, look around you to ensure a safety working area without other people,
animals or any loose objects. And then check for eye protection, proper clothing and
balanced footing.
STARTING/STOPPING THE LINE TRIMMER
Switch ON (Fig. L)
1. Push forward and hold the safety switch on the main handle.
2. Switch the trigger On and hold it. Depress the switch Once the machine starts ,you can
then release the safety button.
Switch OFF
Release the trigger.
NOTE:
Always remove the battery pack from the line trimmer during work breaks and after
finishing work.
Tilt Head Angle adjustment (Fig. M)
Adjust the vertical angle of the trimmer head to fit the trimming conditions.
1. Press the trimmer head angle adjustment button.
2. Adjust the angle of the handle as required and then release the lock adjusting button.
3. Make sure the handle is locked in position.
Lawn edging mode
1. Adjusting your trimmer to the Lawn edging mode- depress the lock button and then
rotate the head 180 degrees.
(Fig. M)
2. Check and adjust the head position is correct for edging.
(Fig. N)
Automatic line feeding
The equipment features a semi automatic single line system. The line will automatically
elongate every time you turn ON & OFF the trimmer.
To make sure the line length is correct, ensure the line is cut off by the guard blade before
restarting it again
.
The line is automatically cut to the correct length by the line cutter.
OPERATION
Trimming
1. Ensure the Trimmer guard blade label has been removed before use. Ensure you wear
gloves when removing this label.
2. Adjust the trimmer head angle to a proper position for trimming operation.
3. Hold the grass trimmer firmly, keeping your balance with feet slightly apart. Alter the
height of the product if needed to ensure an upright posture.
4. Hold the trimmer head just above the ground at an angle of approximately 30°.
5. Move the product slowly from side to side in a swinging motion.
6. Ensure the cutting device remains clean and free from off-cuts that may cause it to
jam. Check regularly. Release the ON/OFF switch and take the battery pack off before
checking.
7. Trim longer grass in stages; do not cut long grass in one cut. For the best results, cut
longer grass in steps.
8. Place the trimmer along the edge of the lawn.
9. Turn product on and push the trimmer forward slowly.
Tips
1. For best results, do not cut wet grass as it tends to stick to the cutting head and guard,
prevents proper discharge of grass trimmings and could cause you to slip and fall.
2. Do not allow the spool cover to drag on the ground or other surfaces.
3. Pay special attention when performing work close to trees and bushes. The cutting head
could damage sensitive bark, and damage fence posts.
4. Fold the plant protector out to avoid bringing the cutting device into contact with hard
objects such as walls and curbstones.
NOTE:
The trimming line will wear faster and require more feeding if the cutting or edging is
done along sidewalks or other abrasive surfaces or heavier weeds are being cut.
Replacing the spool (Fig. O)
1. Press together the cutting head cap tabs and remove the cover.
2. Remove the old spool from the spool cover.
3. Clean out any dirt or grass residue.
4. Put the new spool in the spool housing, thread the line into the hole.
5. Assembly the the spool cover.
Winding the line
NOTE:
Should you wish to wind the line yourself, the instructions are provided below:
Self-winding, however, is NOT recommended because if the line is not wound properly it can
cause the trimmer’s feed system to malfunction or high vibration. For this reason, users are
strongly urged to purchase the pre-wound spool.
1. Wind the line following the directional arrows on the spool housing and hook the end
into the side groove.
