Yanmar ZT370 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 60

background image

SAFETY

12/05

ZT370 Operation Manual

7

CAUTION

Poor Lighting Hazard

Ensure that the work area is adequately
illuminated. Always install wire cages
on portable safety lamps.

Tool Hazard

Always use tools appropriate for the
task at hand and use the correct size
tool for loosening or tightening
machine parts.

Flying Object Hazard

Always wear eye
protection when servicing
the stern-drive or when
using compressed air or
high-pressure water. Dust,
flying debris, compressed

air, pressurized water or steam may
injure your eyes.

Slipping and Tripping Hazard

• Ensure that adequate

floor space is set aside
for servicing the
stern-drive. The floor
space must be flat and
free of holes.

• Keep the floor free of dust, mud,

spilled liquids and parts to help
prevent slipping and tripping.

NOTICE

It is important to perform the daily checks
as listed in this

Operation Manual

.

Periodic maintenance prevents
unexpected downtime, reduces the
number of accidents due to poor engine or
stern-drive performance and can help
extend the life of the engine and
stern-drive.

Always be environmentally
responsible.

Follow the guidelines of the EPA or other
governmental agencies for the proper
disposal of hazardous materials such as
lubrication oil, diesel fuel and engine
coolant. Consult the local authorities or
reclamation facility.

Never dispose of hazardous materials by
dumping them into a sewer, on the ground
or into ground water or waterways.

Before operating the engine, check
stern-drive oil level.

If the stern-drive oil temperature is too
high, stop engine immediately and check
the stern-drive oil level and check the oil
cooler for proper coolant and water flow.

Always tighten components to the
specified torque. Loose parts can cause
equipment damage or cause it to operate
improperly.

ZT370_OM.book 7 ページ２０１３年９月２７日　金曜日　午前１０時１６分

«
...
9
10
11
12
13
...
»

Содержание ZT370





























































Отзывы:

Нет отзывов

Похожие инструкции для ZT370

Бренд: Yamaha Страницы: 86

Бренд: u-blox Страницы: 25

Бренд: Quectel Страницы: 34

Бренд: MSI Страницы: 169

Бренд: Gigabyte Страницы: 125

Бренд: JETWAY Страницы: 2

Fatal1ty 990FX Professional

Бренд: ASROCK Страницы: 287

Бренд: Nuvoton Страницы: 5

S1V30080 Series

Бренд: Seiko Epson Страницы: 10

Бренд: ECS Страницы: 93

Бренд: Texas Instruments Страницы: 13

Бренд: DFI Страницы: 92

Бренд: DFI Страницы: 48

Бренд: JETWAY Страницы: 55

Бренд: Sleipner Страницы: 28

Бренд: Texas Instruments Страницы: 33

Бренд: Intel Страницы: 112

Бренд: ST Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды