Yanmar ZT370 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 60

background image

SAFETY

4

ZT370 Operation Manual

SAFETY PRECAUTIONS

General Information

There is no substitute for common sense
and careful practices. Improper practices
or carelessness can cause burns, cuts,
mutilation, asphyxiation, other bodily injury
or death. This information contains general
safety precautions and guidelines that
must be followed to reduce risk to personal
safety. Special safety precautions are
listed in specific procedures. Read and
understand all of the safety precautions
before operation or performing repairs or
maintenance.

Before You Operate

WARNING

• Never permit anyone to

install or operate the
engine or stern-drive
without proper training.

• Read and understand this

Operation

Manual

before you operate or service

the engine or stern-drive to ensure
that you follow safe operating
practices and maintenance
procedures.

• Safety signs and labels are additional

reminders for safe operating and
maintenance techniques.

• Consult your authorized Yanmar

Marine dealer or distributor for
additional training.

During Operation and
Maintenance

DANGER

Fire Hazard

Ensure that appropriate
fire detection and
extinguishing equipment
are installed and checked
periodically for proper
operation.

Crush Hazard

• Always use lifting

equipment with
sufficient capacity to lift
the stern-drive.

• Never stand under a hoisted

stern-drive. If the hoist mechanism
fails, the stern-drive will fall on you,
causing serious injury or death.

• Never support the stern-drive with

equipment not designed to support
the weight of the stern-drive such as
wooden pieces, blocks or by only
using a jack.

ZT370_OM.book 4 ページ２０１３年９月２７日　金曜日　午前１０時１６分

«
...
6
7
8
9
10
...
»

Содержание ZT370





























































Отзывы:

Нет отзывов

Похожие инструкции для ZT370

Бренд: IBASE Technology Страницы: 58

Pentium P5I430TX/IIB TITANIUM IIB

Бренд: QDI Страницы: 53

CVN X570 GAMING PRO V14

Бренд: Colorful Страницы: 64

Бренд: Portwell Страницы: 86

Бренд: Yamaha Страницы: 114

Бренд: Fastfame Страницы: 41

Бренд: Newport Страницы: 30

Бренд: ASROCK Страницы: 144

Бренд: Supero Страницы: 80

Бренд: ITX SECURITY Страницы: 18

Бренд: Gigabyte Страницы: 147

XtremeDSP Spartan-3A DSP 3400A...

Бренд: Xilinx Страницы: 50

EVB-LAN9252-SPI

Бренд: Microchip Technology Страницы: 22

LANParty Jr. GF9400 T2RS

Бренд: DFI Страницы: 138

Бренд: DFI Страницы: 113

Бренд: ASROCK Страницы: 25

Бренд: Suzuki Marine Страницы: 63

Бренд: Consumer Microcircuits Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды