Yanmar ZT350 series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 58

background image

STERN-DRIVE OPERATION

This section of the Operation Manual

describes the procedures for proper

operation of the stern-drive.

Before you operate the ZT350, read the

following safety information and review the

Safety on page 3.

DANGER

The safety messages that follow have

DANGER level hazards. These safety

messages describe a hazardous

situation which, if not avoided, will

result in death or serious injury.

NEVER permit anyone to

install or operate the engine or

stern-drive without proper

training.

• Read and understand this Operation

Manual before you operate or service the

engine or stern-drive to ensure that you

follow safe operating practices and

maintenance procedures.

• Safety signs and labels are additional

reminders for safe operating and

maintenance techniques.

• See your authorized Yanmar Marine

dealer or distributor for additional training.

ZT350 Operation Manual

21

© 2008 Yanmar Marine International

«
...
23
24
25
26
27
...
»

Содержание ZT350 series



























































Отзывы:

Нет отзывов

Похожие инструкции для ZT350 series

Бренд: Gigabyte Страницы: 51

Бренд: Biostar Страницы: 54

Бренд: IBASE Technology Страницы: 84

Бренд: IBASE Technology Страницы: 64

B85M-P32 series

Бренд: MSI Страницы: 186

Бренд: AXIOMTEK Страницы: 67

Бренд: JETWAY Страницы: 40

Бренд: Microchip Technology Страницы: 34

Fatality H97 Killer series

Бренд: ASROCK Страницы: 109

Бренд: IBASE Technology Страницы: 62

Бренд: Texas Instruments Страницы: 51

NuMaker NUC980 IIoT

Бренд: Nuvoton Страницы: 46

MT9V113PACSTCH-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: Gigabyte Страницы: 120

Бренд: Exar Страницы: 9

P67 PROFESSIONAL

Бренд: ASROCK Страницы: 9

Бренд: Global Страницы: 33

LANPARTY UT 915P-T12

Бренд: DFI Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды