background image

YZ-S5

4

●Even if the machine is to be dismantled and scrapped, someone should be

there to pay attention. Because some harmful substances (such as batteries, waste

oil, etc.) have met the standards, they should be sent to a specific center for

processing.

1.3 Safety requirements for batteries

●The battery must be kept in a low voltage state, and it should be charged as

soon as possible.

●To avoid leakage of electricity, please keep the battery dry and clean, especially

to remove contaminants such as metal dust.

●It is forbidden to place metal parts (such as tools) on the battery to prevent the

battery from being short-circuited and burnt out.

●The charging room should be well ventilated.

●Do not connect or remove the battery when the key switch is in the ON position.

●Before removing or installing batteries, disconnect the negative (-) battery wire

first and then the positive (+) battery wire. When rewiring, be sure to pay attention to

the polarity of the battery, as wrong connection will damage electrical components.

●Avoid direct contact between the positive electrode and the negative electrode,

because it will cause a large current short circuit, high heat and even fire.

1.4 General safety regulations

In addition to the provisions made in this manual, the required general safety

regulations and accident prevention guidelines must also be observed. Even if you

have used a similar sweeper before, please read the instructions carefully. Reading

the instructions beforehand will save you a lot of time in the future. It is vital that you

become familiar with all accessories and controls and their functions before you start

using them. Read through this manual so you don't get scrambled when you turn it on.

Chapter 2 Use of the Machine

2.1 Buttons/pedals of the machine

2.1.1 The core control keys of the machine

Power/Voltmeter (the display device can display the

current power, battery voltage, please charge when the

voltage is lower than 42V).

Key switch

Sweep button

Forward and backward buttons

Speaker button

Headlight button

Sprinkler button

Dust vibration button

Содержание YZ-S5



















Отзывы: