Yamato Pure Line Series Скачать руководство пользователя страница 24

Страница: 24 / 46

4.Operation Method

Sampling the deionized water

①

Press the PUSH key. Sampling of deionized

water is possible. Sampling continues even when
the key is released.

●

n-operation lamp ON

●

The Error

・

Consumables Replacement Display

provides animated display during sampling.

Animated indication during sampling

※

If sampling is not made for a long time, the

quality  of  water  remaining  in  the  unit  may  be
degraded.    Confirm  the  water  quality  display
during  initial  period  of  sampling  and  carry  out
drainage in appropriate timing.

②

Press the PUSH key again, Sampling of

deionized water stops.

●

In-operation lamp OFF

●

Animated indication goes OFF in the Error

・

Consumables

Replacement

Display

during

sampling.

Note1: At initial power application and immediately after replacement of ion exchange resin

cartridge, a certain time period is required till sampling begins because of air remaining in
the ion exchange resin cartridge and piping.

Note2 : The pressure remains in the piping at a time of stopping sampling, which may discharge

small amount of deionized water.

Selecting the water quality unit

Press the UNIT key, and the water quality unit

can be changed.

To change the water quality unit:

●

Electric conductivity (conductivity) display

●

Specific resistance display

※

The unit conversion equation is shown below:

Electric

conductivity

＝

Specific resistance

value

＝

(

Ｓ

ｍ

)

Specific resistance

value (

Ω・ｍ

)

(

Ω・ｍ

)

Electric conductivity

(

Ｓ

ｍ

)

For details, refer to “Electric Conductivity (Conductivity)” of P.22.

Содержание Pure Line Series















































Результаты поиска

Содержание Pure Line Series

Отзывы:

Бренды по названию

Популярные бренды

Yamato Pure Line Series, Руководство пользователя

Результаты поиска

Содержание Pure Line Series

Отзывы:

Бренды по названию

Популярные бренды