Yamato Pure Line Series Скачать руководство пользователя страница 12

Страница: 12 / 46

2. Before operating the unit

Installation procedures

1.Always connect the feed water hose firmly.

●

Take out the feed water hose set (connector main body, feed water hose) from

accessories to the main body. Install the main body on a horizontal stable place close to

the faucet and sink.

●

Unless the connection is firm, the feed water hose or connector may be disconnected,

allowing water to spout.

2. Carry out connection on the faucet side.

(1) Allow the sleeve of socket

③

on the connector side to slide in the direction indicated

with an arrow. Separate the connector main body from the feed water hose.

(2) Loosen the plug

②

from the ring

①

temporarily.

(3) Tighten four set screws

⑤

with equal torque while pressing the ring

①

lightly and

evenly in such a manner that the packing

⑥

contacts the faucet in a flat condition. When

the faucet is a chemical faucet, adjust the position in such a manner that the set screw

⑤

comes to the lowest root of faucet nipple as shown in the figure.

(4) Turn the plug

②

for firm tightening. This will ensure sealing of the faucet and connector

with the packing

⑥

(5) With the sleeve slid in the direction indicated with arrow, insert the plug

②

into the

socket

③

firmly. Connection is completed when the sleeve returns to the original

position when released.

※

If the socket

③

is disconnected, water from the water supply side is interrupted by the

valve provided on the connector main body.

※

Be sure to use the supply water for raw water.

水道栓

接続口本体

接続口側
ソケット

給水ホース

Connector

main body

①

Ring

②

Plug

③

Socket

④

Spacer

⑤

Set

screw

⑥

Packing

⑦

Filter

One-touch

joint

Faucet

Connector
main body

Connector
side socket

Feed water
hose

Faucet
Faucet nipple

Feed water
hose

Sleeve

Содержание Pure Line Series















































Результаты поиска

Содержание Pure Line Series

Отзывы:

Бренды по названию

Популярные бренды

Yamato Pure Line Series, Руководство пользователя

Результаты поиска

Содержание Pure Line Series

Отзывы:

Бренды по названию

Популярные бренды