Yamaha Z150 Скачать руководство пользователя страница 69

Страница: 69 / 91

Maintenance

from that expected.

CAUTION:

ECM00340

●

Be sure to install the thrust washer be-
fore installing the propeller, otherwise
the lower case and propeller boss
could be damaged.

●

Be sure to use a new cotter pin and
bend the ends over securely. Otherwise
the propeller could come off during op-

eration and be lost.

Apply Yamaha marine grease or a cor-
rosion resistant grease to the propeller
shaft.

Install the thrust washer and propeller
on the propeller shaft.

Install the spacer and washer. Tighten
the propeller nut to the specified torque.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NOTE:

If the propeller nut does not align with the
propeller shaft hole after tightening to the
specified torque, tighten the nut further to

align it with the hole.

EMU29281

Changing gear oil

WARNING

EWM00800

●

Be sure the outboard motor is securely
fastened to the transom or a stable
stand. You could be severely injured if
the outboard motor falls on you.

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
or knob is locked. Severe injury could
occur if the outboard motor accidental-

ly falls.

Tilt the outboard motor so that the gear
oil drain screw is at the lowest point pos-
sible.

Place a suitable container under the
gear case.

Remove the gear oil drain screw.

NOTE:

If the magnetic gear oil drain screw
equipped: remove all metal particles from

the screw before installing it.

Remove the oil level plug to allow the oil

1. Gear oil drain screw
2. Oil level plug

ZMU01899

2019 Yamaha Motor Corporation, U.S.A.

Содержание Z150




























































































Результаты поиска

Содержание Z150

Отзывы:

Похожие инструкции для Z150

Бренды по названию

Популярные бренды

Yamaha Z150, Руководство пользователя

Результаты поиска

Содержание Z150

Отзывы:

Похожие инструкции для Z150

Бренды по названию

Популярные бренды