manualshive.com logo in svg

Yamaha YZF-R1, Руководство к набору

Поделиться
Скачать
Yamaha YZF-R1 Скачать руководство пользователя страница 72

– 69 –

Procedure to install the engine (unchangeable)

1.  Attach the two engine adjusting bolts 1 to 

the frame COMP. temporarily.

2.  Fit the engine installation position to the 

frame COMP and attach the bolts 2 and 3 
temporarily.

3.  Attach the bolt 4 temporarily.
4.  Attach the engine mount boss 5 and 6 to 

the frame COMP. temporarily and then 
attach the bolt 7 temporarily.

5.  Tighten the two engine adjusting bolts 1 at 

specified torque.

Check that the bearing surface of the bolts 

1 completely fit the surface of the engine.

6.  Tighten the two nuts 8 and 9 at specified 

torque. Tighten the nut 8 (lower side) at 

first, then tighten the nut 9 (upper side).

7.  Tighten the bolt 4 at specified torque.
8.  Tighten the bolt 7 at specified torque.

FWD

7 5

6

4

3

2

9

8

1

1

TIP

For information about tightening torque 
and requirement for lubricant agent, see 
the list of tightening torque.

Содержание YZF-R1














































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды