Yamaha YZF-R1 2015 Скачать руководство пользователя страница 466 | Manualshive

Страница: 466 / 704

background image

THROTTLE BODIES

7-13

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Place the throttle bodies on a flat surface with

the air filter case side facing up.

b. Install the caps (895-14169-00) onto the hose

fittings “a”.

c. Hold the throttle valves in the open position.

WARNING

EWA15940

When cleaning the throttle bodies, be careful

not to injure yourself on the throttle valves or

other components of the throttle bodies.

NOTICE

ECA20380

• Do not open the throttle valves by supply-

ing electrical power to the throttle bodies.

• Do not use tools to open the throttle valves

or to keep them in the open position.

• Do not open the throttle valves quickly.

d. Apply the recommended cleaning solvent to

the throttle valves and the inside of the throt-
tle bodies to remove any carbon deposits.

TIP

•

Do not allow any cleaning solvent to enter the
opening for the injectors.

•

Do not apply any cleaning solvent to the por-
tions of the throttle valve shafts between the
throttle bodies.

e. Remove the carbon deposits from the inside

of each throttle body in a downward direction,
from the air filter case side of the throttle body
to the engine side.

NOTICE

ECA17590

• Do not use a tool, such as a wire brush, to

remove the carbon deposits; otherwise, the

inside of the throttle bodies may be dam-

aged.

• Do not allow carbon deposits or other for-

eign materials to enter any of the passages

in each throttle body or in the space be-

tween the throttle valve shaft and the throt-

tle body.

f. After removing the carbon deposits, clean the

inside of the throttle bodies with the recom-
mended cleaning solvent, and then dry the
throttle bodies using compressed air.

g. Make sure that there are no carbon deposits

or other foreign materials in any of the pas-
sages “a” in each throttle body or in the space
“b” between the throttle valve shaft and the
throttle body.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

3. Install the throttle bodies.
4. Reset:

•

ISC (Idle Speed Control) learning values
Use the diagnostic code number “67”.
Refer to “SELF-DIAGNOSTIC FUNCTION
AND DIAGNOSTIC CODE TABLE (ECU)” on
page 9-5.

5. Adjust:

•

Throttle bodies synchronizing
Out of specification

o

Replace the throttle

a

a

a

a

a

b

«
...
464
465
466
467
468
...
»

Содержание YZF-R1 2015

































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R1 2015

McPherson Strut MIR 1G00

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: YCF Страницы: 78

TXT PRO - PART LIST 2005

Бренд: GAS GAS Страницы: 38

Бренд: Blata Страницы: 17

Бренд: DYNATEK Страницы: 11

Бренд: DYNATEK Страницы: 12

2005 F4 BRUTALE 910 S

Бренд: MV Agusta Страницы: 195

Бренд: MV Agusta Страницы: 467

Бренд: Can-Am Страницы: 172

Бренд: Lance Страницы: 18

Бренд: X-lite Страницы: 80

SM 500 R E4 2018

Бренд: SWM Страницы: 86

Бренд: 3M Страницы: 77

Бренд: Takegawa Страницы: 10

Бренд: URAL Motorcycles Страницы: 99

Бренд: Yamaha Страницы: 425

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды