Yamaha YXZ10YEXR Скачать руководство пользователя страница 16

Страница: 16 / 222

2-4

BDW-F1696-00

WARNING

• Improper tire pressure or overloading this vehicle may

cause severe injury or death from loss of control or

rollover.

• Never set or allow tire pressure to be below the minimum.

Tire may dislodge from rim.

• VEHICLE LOAD of 0 lb (0 kg) ~ 441 lbs (200 kg)

Recommended: FRONT:

REAR:

Minimum:

FRONT:

REAR:

16 psi

20 psi

15 psi

19 psi

• VEHICLE LOAD of 441 lbs (200 kg ) ~ 668 lbs (303 kg)

Recommended: FRONT:

REAR:

Minimum:

FRONT:

REAR:

16 psi

24 psi

15 psi

23 psi

(110 kPa)

(140 kPa)

(103 kPa)

(131 kPa)

(110 kPa)

(170 kPa)

(103 kPa)

(159 kPa)

* Vehicle load is weight of operator, passenger,

accessories, and cargo. Do not exceed

maximum vehicle load.

Gross Vehicle Weight Rating: 2348 lbs (1065 kg)

maximum including vehicle, weight of operator,

passenger, accessories, and cargo.

OPERATING TIRE PRESSURE: With tires cold, set as follows.

UBDW11E0.book Page 4 Wednesday, June 7, 2023 11:11 AM

Содержание YXZ10YEXR































































































































































































































Результаты поиска

Содержание YXZ10YEXR

Отзывы:

Похожие инструкции для YXZ10YEXR

Бренды по названию

Популярные бренды

Yamaha YXZ10YEXR, Руководство пользователя

Результаты поиска

Содержание YXZ10YEXR

Отзывы:

Похожие инструкции для YXZ10YEXR

Бренды по названию

Популярные бренды