background image

23

Assembly

3-3

 

Using the damper stopper

 

Engaging the damper stopper, located on the performer side in the center of the long frame, 
holds the damper open (letting the tone bars sustain) without having to continuously press the 
damper pedal.

 

While holding the pedal down with your foot, press the stopper knob and remove your foot from 
the pedal. The pedal remains in the lowered positioned and locked.

 

Press on the pedal again to automatically disengage the stopper and restore normal operation.

 

*  If pedal height adjustment in step 

3-1

 “Pedal height adjustment” is set too low, the damper stopper 

may not function properly. Please set the space between the bottom of the pedal and the floor to more 
than 2cm.

Damper stopper

The stopper slides in between the adjustment nut 
and the main unit to hold the damper open.

4

  Adjusting the tone bar height

When loosening the slide guide fixing bolts be sure to hold down the side frame 
from above. The side frame can suddenly rise which is extremely dangerous.

 

CAUTION

Holding down both low and high register side side frames, loosen the slide guide fixing bolts.
After adjusting the instrument to a comfortable height, tighten the slide guide fixing bolts to secure. 
Use the guide lines on the slide legs as a reference and adjust the height so that the instrument’s 
playing surface is parallel to the floor.

A gas spring system is incorporated into one of the legs on the high register end, and another leg 
on the low register end. When the slide guide fixing bolts are loosened on the low register side, 
the side attached to the leg without the gas spring may slightly lower (diagram 

A

) however, this is 

not a sign of any problem. When adjusting instrument height, slightly lift up on the side that is not 
equipped with the gas spring.

After assembly is complete, make sure all nuts and bolts are tightened firmly.

The brown felt attached to both sides of the glockenspiel’s main unit and the cardboard attached at two positions 
on the low register side are part of the packing materials used to hold the tone bars in place. After assembly is com-
plete, pull on the felt and cardboard to remove.

Slide guide 

fixing bolt

Without gas springs

Equipped with gas springs

Guide 

lines

A

02_yg2500_en_new.indd   23

14/08/26   11:25

Содержание YGRD-2500














Отзывы: