manualshive.com logo in svg

Yamaha YFM700RF, Руководство пользователя

Поделиться
Скачать
Yamaha YFM700RF Скачать руководство пользователя страница 75

7-5

7

Pre-operation checks

Always inspect your ATV each time you use it to
make sure the ATV is in safe operating condition.
Perform the pre-operation checks listed on page
5-1. Always follow the inspection and mainte-
nance procedures and schedules described in the
Owner’s Manual. 

WARNING! Failure to inspect

the ATV before operating it and to maintain it
properly increases the possibility of an acci-
dent or equipment damage.

 [EWB01432]

Speed limiter

For riders less experienced with this model, the
throttle lever housing is equipped with a speed
limiter. The speed limiter keeps the throttle from

fully opening, even when the throttle lever is
pushed to the maximum. Turning in the adjusting
screw limits the maximum engine power available
and decreases the maximum speed of the ATV.
Turning in the adjusting screw decreases top
speed, and turning it out increases top speed.
(See page 4-5.)

Loading and accessories

WARNING

EWB00973

Improper loading or towing can increase the
risk of loss of control, an overturn, or other ac-
cident. To reduce the risk of an accident:

1. Locknut
2. Adjusting screw

1

2

U2LS60E0.book  Page 5  Wednesday, June 18, 2014  11:12 AM

Содержание YFM700RF

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды