Yamaha YFM700RF Скачать руководство пользователя

Страница: 106 / 160

8-14

Be sure the engine oil is at the correct lev-
el, otherwise engine damage may result.

[ECB00852]

TIP

When adding oil, be careful not to overfill the en-
gine oil tank; the oil level rises faster starting from
the half-level-portion on the dipstick.

6. Insert the dipstick into the engine oil tank filler

hole, and then tighten the engine oil tank filler
cap.

NOTICE:

Make sure that the engine oil

tank filler cap is securely tightened; other-
wise, oil may seep out when the engine is
running.

[ECB00363]

To change the engine oil (with or without oil fil-
ter element replacement)

1. Place the ATV on a level surface.
2. Start the engine, warm it up for several minu-

tes, and then turn it off.

3. Place an oil pan under the engine to collect

the used oil.

4. Remove the crankcase engine oil filler cap

and its O-ring, and then remove the crank-
case engine oil drain bolt and its gasket.

1. Crankcase engine oil filler cap
2. O-ring

1. Crankcase engine oil drain bolt
2. Gasket

U2LS60E0.book Page 14 Wednesday, June 18, 2014 11:12 AM

Содержание YFM700RF

































































































































































Результаты поиска

Содержание YFM700RF

Отзывы:

Похожие инструкции для YFM700RF

Бренды по названию

Популярные бренды

Yamaha YFM700RF, Руководство пользователя

Результаты поиска

Содержание YFM700RF

Отзывы:

Похожие инструкции для YFM700RF

Бренды по названию

Популярные бренды