Yamaha YFM700RF страница 129 Скачать руководство пользователя

Страница: 129 / 160

8-37

The clutch lever free play should measure 8.0–
13.0 mm (0.31–0.51 in) as shown. If the free play is
incorrect, adjust it as follows.

1. Slide the rubber cover back.
2. Loosen the locknut at the clutch lever.
3. To increase the clutch lever free play, turn the

adjusting bolt at the clutch lever in direction
(a), and to decrease it, turn the bolt in direc-
tion (b).

TIP

If the specified clutch lever free play could be ob-
tained as described above, skip steps 4–7.

4. Fully turn the adjusting bolt at the clutch lever

in direction (a) to loosen the clutch cable.

5. Loosen the locknut at the crankcase.
6. To increase the clutch lever free play, turn the

adjusting nut at the crankcase in direction (a),
and to decrease it, turn the nut in direction (b).

7. Tighten the locknut at the crankcase.

1. Rubber cover
2. Clutch lever free play adjusting bolt
3. Locknut
4. Clutch lever free play

(a)

(b)

1. Locknut
2. Clutch lever free play adjusting nut

(a)

(b)

U2LS60E0.book Page 37 Wednesday, June 18, 2014 11:12 AM

Содержание YFM700RF

































































































































































Результаты поиска

Содержание YFM700RF

Отзывы:

Похожие инструкции для YFM700RF

Бренды по названию

Популярные бренды

Yamaha YFM700RF, Руководство пользователя

Результаты поиска

Содержание YFM700RF

Отзывы:

Похожие инструкции для YFM700RF

Бренды по названию

Популярные бренды