Yamaha YFM4FAR Скачать руководство пользователя страница 309

Страница: 309 / 397

8 - 29

CHAS

STEERING SYSTEM

REMOVING THE REAR BRAKE SWITCH

1.Remove:

●

Rear brake switch

NOTE:

Push the fastener when removing the rear
brake switch out of the rear brake lever holder.

CHECKING THE HANDLEBAR

1.Check:

●

Handlebar
Bends/cracks/damage

→

Replace.

WARNING

Do not attempt to straighten a bent
handlebar as this may dangerously weaken
the handlebar.

INSTALLING THE HANDLEBAR

1.Install:

●

Handlebar

●

Handlebar holders

NOTE:

The upper handlebar holder should be
installed with the punched mark

forward

CAUTION:

First tighten the bolts

on the front side of

the handlebar holder, and then tighten the
bolts

on the rear side.

23 Nm (2.3 m • kg, 17 ft • lb)

INSTALLING THE REAR BRAKE LEVER

1.Install:

●

Handlebar switch

●

Rear brake lever

●

Lever bracket

NOTE:

Install the lever bracket as shown.

80 mm (3.1 in)

Содержание YFM4FAR














































































































































































































































































































































































































Результаты поиска

Содержание YFM4FAR

Отзывы:

Похожие инструкции для YFM4FAR

Бренды по названию

Популярные бренды

Yamaha YFM4FAR, Руководство по обслуживанию

Результаты поиска

Содержание YFM4FAR

Отзывы:

Похожие инструкции для YFM4FAR

Бренды по названию

Популярные бренды