manualshive.com logo in svg

Yamaha YFM4FAR, Руководство по обслуживанию

Yamaha YFM4FAR - это надежный квадроцикл с мощным двигателем. Для обслуживания и ремонта инструкция в формате Service Manual доступна для загрузки бесплатно на manualshive.com. Получите свой экземпляр сегодня и следуйте высокому качеству Yamaha.

Поделиться
Скачать
background image

CHAS

CHAPTER 8.

CHASSIS

FRONT AND REAR WHEELS 

..................................................................... 8-1

FRONT WHEELS .................................................................................. 8-1
REAR WHEELS  .................................................................................... 8-2
CHECKING THE WHEELS  ................................................................... 8-3
CHECKING THE WHEEL HUBS  .......................................................... 8-3
CHECKING THE BRAKE DISCS  .......................................................... 8-4
INSTALLING THE WHEEL HUBS  ........................................................ 8-4
INSTALLING THE WHEELS  ................................................................. 8-4

FRONT BRAKE 

............................................................................................ 8-6

FRONT BRAKE PADS  .......................................................................... 8-6
REPLACING THE FRONT BRAKE PADS  ............................................ 8-7
FRONT BRAKE MASTER CYLINDER .................................................. 8-9
CHECKING THE MASTER CYLINDER  .............................................. 8-11
ASSEMBLING THE FRONT BRAKE MASTER CYLINDER  ............... 8-11
INSTALLING THE FRONT BRAKE MASTER CYLINDER  ................. 8-12
FRONT BRAKE CALIPER  .................................................................. 8-14
DISASSEMBLING THE FRONT BRAKE CALIPERS  ......................... 8-16
CHECKING THE FRONT BRAKE CALIPERS .................................... 8-16
ASSEMBLING THE FRONT BRAKE CALIPERS  ............................... 8-17
INSTALLING THE FRONT BRAKE CALIPERS .................................. 8-17

REAR BRAKE 

............................................................................................ 8-19

REMOVING THE REAR BRAKE  ........................................................ 8-23
CHECKING THE REAR BRAKE  ......................................................... 8-24
INSTALLING THE REAR BRAKE  ....................................................... 8-25

STEERING SYSTEM 

.................................................................................. 8-28

HANDLEBAR ...................................................................................... 8-28
REMOVING THE REAR BRAKE SWITCH  ......................................... 8-29
CHECKING THE HANDLEBAR  .......................................................... 8-29
INSTALLING THE HANDLEBAR  ........................................................ 8-29
INSTALLING THE REAR BRAKE LEVER  .......................................... 8-29
INSTALLING THE MASTER CYLINDER ASSEMBLY ........................ 8-30
STEERING STEM  ............................................................................... 8-31
REMOVING THE BEARING RETAINER  ............................................ 8-33
CHECKING THE STEERING STEM ................................................... 8-33
INSTALLING THE BEARING RETAINER ........................................... 8-33
INSTALLING THE CABLE GUIDE  ...................................................... 8-33
TIE RODS AND STEERING KNUCKLES  ........................................... 8-34
REMOVING THE STEERING KNUCKLES ......................................... 8-36
CHECKING THE TIE RODS  ............................................................... 8-36
CHECKING THE STEERING KNUCKLES  ......................................... 8-36
INSTALLING THE TIE RODS  ............................................................. 8-39

Содержание YFM4FAR














































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM4FAR

Taylor-Dunn GT-370 Operation And Maintenance Manual preview
GT-370
Бренд: Taylor-Dunn Страницы: 109
Bad Boy 2013 RECOIL iS Owner'S Manual preview
2013 RECOIL iS
Бренд: Bad Boy Страницы: 56
Arctic Cat 120 Sno Pro 2010 Service Manual preview
120 Sno Pro 2010
Бренд: Arctic Cat Страницы: 562
Fuelfix Tanks2Go 1200lt Mobile Fuel Tank Trailer User Manual preview
Tanks2Go 1200lt Mobile Fuel Tank Trailer
Бренд: Fuelfix Страницы: 17
DAELIM ET-250 Specifications preview
ET-250
Бренд: DAELIM Страницы: 1
Apogee Adapt-X 300 User Manual preview
Adapt-X 300
Бренд: Apogee Страницы: 24
Toro twister Operator'S Manual preview
twister
Бренд: Toro Страницы: 32
Polaris Sportsman 9920364 Owner'S Manual preview
Sportsman 9920364
Бренд: Polaris Страницы: 143
YBIKE Explorer Owner'S Manual preview
Explorer
Бренд: YBIKE Страницы: 12
Moni XMX610 Operating Instructions And Assembly Manual preview
XMX610
Бренд: Moni Страницы: 16
NC ENGINEERING MKII 600 Series Operating, Maintenance And Safety Instructions preview
MKII 600 Series
Бренд: NC ENGINEERING Страницы: 80
KAYO MOTOR AU125 Service Manual preview
AU125
Бренд: KAYO MOTOR Страницы: 91
Ski-Doo 2006 MX X Operator'S Manual preview
2006 MX X
Бренд: Ski-Doo Страницы: 28
Baja motorsports CN90U-2 Owner'S Manual preview
CN90U-2
Бренд: Baja motorsports Страницы: 77
BERG Extra Theme User Manual preview
Extra Theme
Бренд: BERG Страницы: 8
DFK CF MOTO CFORCE 625 Installation Instructions Manual preview
CF MOTO CFORCE 625
Бренд: DFK Страницы: 64
Yamaha RS90GTL Owner'S Manual preview
RS90GTL
Бренд: Yamaha Страницы: 104
Yamaha RS90GTW Owner'S Manual preview
RS90GTW
Бренд: Yamaha Страницы: 110

Бренды по названию

Популярные бренды

Загрузить еще бренды