Yamaha YFM4FAR Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 397

background image

3 - 47

CHK

ADJ

CHECKING THE STEERING SYSTEM

1.Place the machine on a level surface.
2.Check:

●

Steering assembly bushings
Move the handlebar up and down, and/or
back and forth.
Excessive play

→

Replace the steering stem

bearing.

3.Check:

●

Tie-rod ends
Turn the handlebar to the left and/or right
until it stops completely, then move the
handlebar from the left to the right slightly.
Tie-rod end has any vertical play

→

Replace

the tie-rod end.

4.Raise the front end of the machine so that

there is no weight on the front wheels.

5.Check:

●

Ball joints and/or wheel bearings
Move the wheels laterally back and forth.
Excessive free play

→

Replace the front

arms (upper and lower) and/or wheel
bearings.

ADJUSTING THE TOE-IN

1.Place the machine on a level surface.
2.Measure:

●

Toe-in
Out of specification

→

Adjust.

*****************************************************

Measurement steps:

NOTE:

Before measuring the toe-in, make sure that
the tire pressure is correct.

●

Mark both front tire tread centers.

●

Face the handlebar straight ahead.

Toe-in:

0 ~ 10 mm (0 ~ 0.39 in)
(with tires touching the ground)

CHECKING THE STEERING SYSTEM/

ADJUSTING THE TOE-IN

«
...
108
109
110
111
112
...
»

Содержание YFM4FAR














































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM4FAR

Бренд: KAYO MOTO Страницы: 9

Бренд: MANCO Страницы: 8

Бренд: E-Z-GO Страницы: 66

Бренд: Ezgo Страницы: 102

ski-doo REV GEN4 TOURING ACE

Бренд: BRP Страницы: 340

TERRAIN DX4 CAB

Бренд: CORVUS Страницы: 136

Бренд: Egholm Страницы: 12

Бренд: PRONAR Страницы: 131

PTV 4x4 Series 10

Бренд: Polaris Страницы: 127

Бренд: Polaris Страницы: 153

Roketa ATV-08L-90

Бренд: Scooter Dynasty Страницы: 12

Бренд: Baja Страницы: 180

Бренд: Baja Страницы: 82

Бренд: GAS GAS Страницы: 36

Бренд: Razor Страницы: 12

Бренд: Yamaha Страницы: 170

Бренд: Land Pride Страницы: 96

Sportsman BIG BOSS 6x6

Бренд: Polaris Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды