3 - 48
INSP
ADJ
TOE-IN ADJUSTMENT
●
Face the handlebar straight ahead.
●
Measure the width
Å
between the marks.
●
Rotate the front tires 180˚ until the marks
are exactly opposite one another.
●
Measure the width
ı
between the marks.
●
Calculate the toe-in using the formula
given below.
●
If the toe-in is incorrect, adjust it.
*********************************
3.Adjust:
●
Toe-in
WARNING
●
Be sure that both tie-rods are turned the
same amount. If not, the machine will
drift right or left even though the handle-
bar is positioned straight. This may lead
to mishandling and an accident.
●
After setting the toe-in to specification, run
the machine slowly for some distance with
both hands lightly holding the handlebar
and check that the handlebar responds cor-
rectly. If not, turn either the right or left tie-
rod within the toe-in specification.
*********************************
Adjustment steps:
●
Mark both tie-rods ends.
This reference point will be needed during
adjustment.
●
Loosen the locknuts (tie-rod end)
1
of
both tie-rods.
●
The same number of turns should be
given to both the right and left tie-rods
2
until the specified toe-in is obtained. This
is to keep the length of the rods the same.
●
Tighten the rod end locknuts of both tie rods.
NOTE:
Adjust the rod ends so that A and B are
equal.
*********************************
Toe-in =
ı
–
Å
T
R
.
.
Locknut (rod end):
15 Nm (1.5 m • kg, 11 ft • lb)
Содержание YFM400FWA 2000 5GH3-AE1
