Yamaha XT250 2024 Скачать руководство пользователя страница 55

Страница: 55 / 96

Periodic maintenance and adjustment

7-16

3. Pull the air filter element out.
4. Insert a new air filter element into

the air filter case as shown.

NOTICE:

Make sure that the air

filter element is properly seated
in the air filter case. The engine
should never be operated with-
out the air filter element in-
stalled, otherwise the piston(s)
and/or cylinder(s) may become
excessively worn.

[ECA10482]

5. Install the air filter case cover by in-

stalling the screws.

6. Install the seat.

To clean the air filter check hose

1. Check the hose on the side of the

air filter case for accumulated dirt
or water.

2. If dirt or water is visible, remove

the hose, clean it, and then install
it.

1. Screw

2. Air filter case cover

1. Air filter element

2. Air filter case

3. Slot

1. Air filter check hose

B1U-9-75-E0.book 16 ページ２０２３年４月２０日　木曜日　午後１時５３分

Содержание XT250 2024

































































































Результаты поиска

Содержание XT250 2024

Отзывы:

Похожие инструкции для XT250 2024

Бренды по названию

Популярные бренды

Yamaha XT250 2024, Руководство пользователя

Результаты поиска

Содержание XT250 2024

Отзывы:

Похожие инструкции для XT250 2024

Бренды по названию

Популярные бренды