Yamaha XSR700M 2020 Скачать руководство пользователя страница 55

Страница: 55 / 104

Perio

ic maintenance an

justment

7-11

4. If the engine oil is below the mini-

mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.

TIP

Check the O-ring for damage, and re-
place it if necessary.

To chan

e the en

ine oil (with or

without oil filter cartri

e replace-

ment)

1. Place the vehicle on a level surfa-

ce.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Place an oil pan under the engine

to collect the used oil.

4. Remove the engine oil filler cap,

the engine oil drain bolt and its
gasket to drain the oil from the
crankcase.

TIP

Skip steps 5–7 if the oil filter cartridge
is not being replaced.

5. Remove the oil filter cartridge with

an oil filter wrench.

1. Engine oil filler cap
2. Engine oil level check window
3. Maximum level mark
4. Minimum level mark

3
4

1. Engine oil filler cap
2. O-ring

1. Engine oil drain bolt
2. Gasket

1. Oil filter wrench
2. Oil filter cartridge

UB2G11E0.book Page 11 Monday, January 7, 2019 1:13 PM

Содержание XSR700M 2020









































































































Результаты поиска

Содержание XSR700M 2020

Отзывы:

Похожие инструкции для XSR700M 2020

Бренды по названию

Популярные бренды

Yamaha XSR700M 2020, Руководство пользователя

Результаты поиска

Содержание XSR700M 2020

Отзывы:

Похожие инструкции для XSR700M 2020

Бренды по названию

Популярные бренды