Yamaha XSR700M 2020 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 104

background image

Perio

d

ic maintenance an

d

a

d

justment

7-19

7

EAU21963

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.



The wheel rims should be
checked for cracks, bends, warp-
age or other damage before each
ride. If any damage is found, have
a Yamaha dealer replace the
wheel. Do not attempt even the
smallest repair to the wheel. A de-
formed or cracked wheel must be
replaced.



The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

EAU33893

A

d

justin

g

the clutch lever free

play

Measure the clutch lever free play as
shown.

Periodically check the clutch lever free
play and, if necessary, adjust it as fol-
lows.
To increase the clutch lever free play,
turn the clutch lever free play adjusting
bolt at the clutch lever in direction (a).
To decrease the clutch lever free play,
turn the adjusting bolt in direction (b).

TIP

If the specified clutch lever free play
cannot be obtained as described
above, proceed as follows.

1. Fully turn the adjusting bolt at the

clutch lever in direction (a) to loos-
en the clutch cable.

2. Loosen the locknut at the crank-

case.

3. To increase the clutch lever free

play, turn the clutch lever free play
adjusting nut in direction (a). To
decrease the clutch lever free
play, turn the adjusting nut in di-
rection (b).

4. Tighten the locknut.

1. Clutch lever free play adjusting bolt
2. Clutch lever free play

Clutch lever free play:

5.0–10.0 mm (0.20–0.39 in)

2

1

(b)

(a)

1. Locknut
2. Clutch lever free play adjusting nut

1

2

(a)

(b)

UB2G11E0.book Page 19 Monday, January 7, 2019 1:13 PM

«
...
61
62
63
64
65
...
»

Содержание XSR700M 2020









































































































Отзывы:

Нет отзывов

Похожие инструкции для XSR700M 2020

Бренд: AJP Страницы: 191

F 850 GS Adventure 2019

Бренд: BMW Motorrad Страницы: 346

Бренд: Honda Страницы: 112

Бренд: Ohlins Страницы: 8

Бренд: Memphis Shades Страницы: 2

Бренд: Suzuki Страницы: 230

Бренд: GAS GAS Страницы: 131

Бренд: Serpento Страницы: 66

Бренд: DYNATEK Страницы: 4

Бренд: Mastech Страницы: 2

Бренд: digades Страницы: 10

Бренд: Palm Страницы: 14

Бренд: Aosom Страницы: 25

Бренд: Star Motorcycles Страницы: 19

Бренд: Abus Страницы: 35

Бренд: hepco & becker Страницы: 3

Бренд: Gilera Страницы: 80

Бренд: KTM Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды