Appendix
XMV
8
2
8
0/XMV
8
140/XMV
8
2
8
0-D/XMV
8
140-D O
w
ner’s Man
u
al
27
If a problem occurs in the XMV, the [ALERT] indicator will flash and an alert number will appear in the display.
The alert numbers, the corresponding content, and the appropriate actions are listed below.
Alert Numbers and Content
Alert number
Meanin
g
Response
No display
(only [ALERT] is lit)
The de
v
ice has not started
u
p correctly.
T
u
rn the po
w
er off, then t
u
rn on after
w
aiting at least 5
seconds. If this does not sol
v
e the pro
b
lem, please ini-
tialize the memory. Sho
u
ld this also fails, contact yo
u
r
Yamaha dealer.
001.–00
8
.
010.
The internal
b
ack
u
p
b
attery has
b
een completely
exha
u
sted or is not installed.
When yo
u
t
u
rn off the po
w
er, the c
u
rrent settings
w
ill
b
e
lost, and
w
ill ret
u
rn to the defa
u
lt
v
al
u
es. Please stop
u
se
immediately, and contact yo
u
r Yamaha dealer.
011.
The internal
b
ack
u
p
b
attery has r
u
n extremely lo
w
, and
it is possi
b
le that the internal memory has
b
een cleared.
012.
The internal
b
ack
u
p
b
attery has only a small amo
u
nt of
po
w
er remaining.
This does not affect the operation of the de
v
ice. Ho
w
-
e
v
er, if yo
u
contin
u
e
u
sing the de
v
ice, the settings may
b
e lost and reset to the defa
u
lt
v
al
u
es. Contact yo
u
r
Yamaha dealer as soon as possi
b
le.
013.
A pro
b
lem has occ
u
rred
w
ith the internal clock, and it
has
b
een initialized (Jan
u
ary 1, 2000, 0:00)
If this occ
u
rs each time yo
u
t
u
rn on the po
w
er, it is possi-
b
le that the internal
b
ack
u
p
b
attery has r
u
n do
w
n or that
the de
v
ice has malf
u
nctioned. Contact yo
u
r Yamaha
dealer.
If this occ
u
rs only once, an a
b
normality
w
as detected
w
ith the clock setting and it
w
as initialized;
u
se MTX Edi-
tor to set the time.
015.
The settings sa
v
ed in internal memory ha
v
e
b
een lost.
Either the internal
b
ack
u
p
b
attery has r
u
n lo
w
, or the
de
v
ice has malf
u
nctioned. Contact yo
u
r Yamaha dealer.
016.
A memory pro
b
lem has occ
u
rred.
Contact yo
u
r Yamaha dealer.
021.
The
w
ord clock master has
b
ecome
u
nlocked.
Make s
u
re that the
w
ord clock signal is
b
eing inp
u
t cor-
rectly.
022.
The digital signal
b
eing inp
u
t to the [YDIF IN] connector
is not synchronized to the
w
ord clock of this de
v
ice.
Make s
u
re that YDIF ca
b
les are properly connected.
Use ca
b
les that meet the req
u
ired specifications.
023.
The digital signal
b
eing inp
u
t to the [YDIF IN] connector
is not contin
u
o
u
sly synchronized to the
w
ord clock of
this de
v
ice.
030.
There is a pro
b
lem
w
ith the connection of the [YDIF IN]
connector.
Make s
u
re that YDIF ca
b
les are properly connected.
Use ca
b
les that meet the req
u
ired specifications.
040.
D
u
plicate IP addresses.
Change the IP addresses so that there are no d
u
pli-
cates.
041.
IP address
w
as not set
w
ithin 60 seconds of start
u
p.
Please check rear panel DIP s
w
itch 6 (IP Setting). If DIP
s
w
itch 6 is set to “PC,”
u
se MTX Editor or DHCP ser
v
er
to specify the de
v
ice IP address.
043.
Too many de
v
ices are connected to the net
w
ork.
Red
u
ce the n
u
m
b
er of de
v
ices connected to the net-
w
ork.
050.
The UNIT ID is set to “00.”
Set the UNIT ID to something other than “00.”
051.
De
v
ices
w
ith identical UNIT IDs
w
ere fo
u
nd connected
w
ithin the same net
w
ork.
Change the UNIT ID so that there are no d
u
plicates.
100.
The po
w
er s
u
pply
w
as sh
u
t do
w
n
b
eca
u
se d.c.
w
as
detected on a speaker o
u
tp
u
t.
It is likely that the de
v
ice has malf
u
nctioned; immediately
stop
u
sing the de
v
ice and contact yo
u
r Yamaha dealer.
101.
The po
w
er s
u
pply
w
as sh
u
t do
w
n
b
eca
u
se its tempera-
t
u
re exceeded the allo
w
ed limit.
T
u
rn the po
w
er off, let the po
w
er s
u
pply cool do
w
n, then
t
u
rn the po
w
er on again.
Contin
u
o
u
s high-po
w
er o
u
tp
u
t
w
ill ca
u
se high tempera-
t
u
res, so please lo
w
er the o
u
tp
u
t le
v
el. If the temperat
u
re
is still high, check
w
hether dirt or a foreign o
b
ject co
u
ld
ha
v
e clogged the cooling fan, and clean the fan if neces-
sary.
