background image

Smart key system

4-9

4

2. The turn signal lights flash once

and the vehicle power turns off.

TIP

When the main switch is turned to
“OFF” but the smart key cannot be
confirmed (the smart key is either out-
side operation range or has been
turned off), the beeper will sound for 3
seconds and the smart key system in-
dicator light will flash for 30 seconds.

During this 30 seconds, the main
switch can be freely operated.

After 30 seconds, the vehicle
power will turn off automatically.

To turn the vehicle power off im-
mediately, push the main switch
knob four times within 2 seconds.

EAU79042

OPEN (open)

Power is supplied to the main switch.
The seat and storage compartment A
can be opened.

To open the seat and storage compart-
ment A

1. With the smart key turned on and

within operating range, push the
main switch knob.

2. While the smart key system indi-

cator light is on, turn the main
switch to “OPEN”.

3. To open the seat, push the

“SEAT” button, and then lift the
rear of the seat.

4. To open storage compartment A,

push the “LID” button.

1. Push.
2. Turn.

1

2

1. “SEAT” button

1

UB5X10E0.book  Page 9  Thursday, May 27, 2021  8:55 AM

Содержание XMAX 2022



























































































































Отзывы: