manualshive.com logo in svg

Yamaha WR250F(R), Инструкция по сборке, Страница: 33 / 34

Поделиться
Скачать
Yamaha WR250F(R) Скачать руководство пользователя страница 33

-27-

Rear wheel axle and nut

M20

x

1.5

125

12.5

90

Driven sprocket and wheel hub

M 8

x

1.25

50

5.0

36

Nipple (spoke)

-

3

0.3

2.2

Disc cover and rear brake caliper

M 6

x

1.0

7

0.7

5.1

Protector and rear brake caliper

M 6

x

1.0

7

0.7

5.1

Chain puller adjust bolt and locknut

M 8

x

1.25

16

1.6

11

Engine mounting:
Engine lower bracket and frame

M 8

x

1.25

34

3.4

24

Engine upper bracket and fram

M 8

x

1.25

34

3.4

24

Engine and engine bracket (front)

M10

x

1.25

69

6.9

50

Engine and engine bracket (upper)

M10

x

1.25

55

5.5

40

Engine and frame (lower)

M10

x

1.25

69

6.9

50

Engine guard (lower)

M 6

x

1.0

10

1.0

72

Engine guard (left/ right)

M 8

x

1.25

23

2.3

17

Pivot shaft and nut

M16

x

1.5

85

8.5

61

Relay arm and swingarm

M14

x

1.5

80

8.0

58

Relay arm and connecting rod

M14

x

1.5

80

8.0

58

Connecting rod and frame 

M14

x

1.5

80

8.0

58

Rear shock absorber and frame

M10

x

1.25

56

5.6

40

Rear shock absorber and relay arm

M10

x

1.25

53

5.3

38

Rear frame and frame (upper)

M 8

x

1.25

32

3.2

23

Rear frame and frame (lower)

M 8

x

1.25

29

2.9

21

Swingarm and brake hose holder

M 5

x

0.8

1

0.1

0.7

Swingarm and patch

M 4

x

0.7

2

0.2

1.4

Drive chain tensioner mounting (upper)

M 8

x

1.25

19

1.9

13

Drive chain tensioner mounting (lower)

M 8

x

1.25

20

2.0

14

Chain support and swingarm

M 6

x

1.0

7

0.7

5.1

Seal guard and swingarm

M 5

x

0.8

6

0.6

4.3

Fuel tank mounting

M 6

x

1.0

10

1.0

7.2

Fuel tank and fuel cock

M 6

x

1.0

7

0.7

5.1

Fuel tank and seat set bracket

M 6

x

1.0

7

0.7

5.1

Fuel tank and hooking screw (fitting band)

M 6

x

1.0

7

0.7

5.1

Seat mounting

M 8

x

1.25

23

2.3

17

Side cover mounting

M 6

x

1.0

7

0.7

5.1

Front fender mounting

M 6

x

1.0

7

0.7

5.1

Rear fender mounting (front)

M 6

x

1.0

7

0.7

5.1

Rear fender mounting (rear)

M 6

x

1.0

10

1.0

7.2

Trip meter mounting

M 6

x

1.0

7

0.7

5.1

Meter cable holder

M 5

x

0.8

4

0.4

2.9

Headlight (left/ right)

M 6

x

1.0

10

1.0

7.2

Headlight (lower)

M 6

x

1.0

7

0.7

5.1

Taillight

M 6

x

1.0

4

0.4

2.9

Taillight lead clamp and rear fender

M 4

x

1.59

0.5

0.05

0.36

Coolant reservoir

M 6

x

1.0

7

0.7

5.1

Sidestand bracket

M10

x

1.25

66

6.6

48

Sidestand

M10

x

1.25

64

6.4

46

Item

Thread size

Tightening torque

Nm

m

d

kg

ft

d

lb

Содержание WR250F(R)



































Отзывы:

Нет отзывов