Yamaha WR250F(R) Скачать руководство пользователя страница 28

Страница: 28 / 34

-22-

EAA01069

M. ADJUSTING THE HOT

STARTER (CHOKE) CABLE

FREE PLAY

1. Measure:

hot starter (choke) cable free play (c)

Out of specification

Adjust.

Hot starter (choke) cable free play

3 ~ 6 mm (0.12 ~ 0.24 in)

2. Adjust:

hot starter (choke) cable free play

a. Loosen the locknut (1).
b. Turn the adjusting bolt (2) in direction

(a) or (b) until the specified hot starter
(choke) cable free play is obtained.

Direction (a):

Hot starter (choke) cable free play
is increased.

Direction (b):

Hot starter (choke) cable free play
is decreased.

c. Tighten the locknut.

NOTE:

After adjustment, check proper operation
of hot starter (choke).

2. Adjust:

clutch cable free play

a. Loosen the locknuts (1).
b. Adjust the free play by changing their

tightening position.

c. Tighten the locknuts.

EAA01059

N. ADJUSTING THE DRIVE CHAIN

SLACK

NOTE:

The drive chain slack must be checked
above the drive chain guide bolt.

CAUTION:

A drive chain that is too tight will over-
load the engine and other vital parts,
and one that is too loose can skip and
damage the swingarm or cause an
accident. Therefore, keep the drive
chain slack within the specified limits.

1. Stand the machine on a level surface.

Securely support the machine so that
there is no danger of it falling over.

NOTE:

Both wheels should be on the ground
without a rider on the machine.

2. Rotate the rear wheel several times.
3. Measure:

drive chain slack (a)

Out of specification

Adjust.

Drive chain slack:

40 ~ 50 mm (1.6 ~ 2.0 in)

4. Loosen:

wheel axle nut (1)

5. Adjust:

drive chain slack

a. Loosen both locknuts (3).
b. Turn both adjusting bolts (2) in direc-

tion (a) or (b) until the specified drive
chain slack is obtained.

Direction (a):

Drive chain is tightened.

Direction (b):

Drive chain is loosened.

NOTE:

To maintain the proper wheel alignment,
adjust both sides evenly.

c. Tighten the wheel axle nut to specifica-

tion.

Wheel axle nut:

125 Nm (12.5 m

kg, 90 ft

lb)

d. Tighten the locknuts to specification.

Locknut:

16 Nm (1.6 m

kg, 11 ft

lb)

NOTE:

Make minute adjustment on the lever
side using the adjusting dial (2).

After adjustment, check proper
operation of clutch lever.

Содержание WR250F(R)



































Результаты поиска

Содержание WR250F(R)

Отзывы:

Бренды по названию

Популярные бренды

Yamaha WR250F(R), Инструкция по сборке

Результаты поиска

Содержание WR250F(R)

Отзывы:

Бренды по названию

Популярные бренды