Yamaha WaveRunner VX Deluxe 2007 Скачать руководство пользователя | Manualshive

Страница: 65 / 96

background image

Operation

58

start the engine, and then look in all direc-
tions before starting off.

WARNING

EWJ00610

Before starting off, make sure that there
are no boats, swimmers, or obstacles
around you.

EJU33161

Boarding with passengers

WARNING

EWJ00660

Severe internal injuries can occur if water
is forced into body cavities as a result of
being near the jet thrust nozzle. Do not ap-
ply throttle until the passengers are seated
with their feet on the floor of the footwell
and are securely holding on to the person
in front of them or to the handgrip provid-
ed.

(1) Climb on board as noted in the previous

section, and sit astride the seat.

(2) Attach the engine shut-off cord to your left

wrist, and then attach the clip to the en-
gine shut-off switch.

(3) Have the passengers move to the rear of

the watercraft.

(4) Have a passenger board and sit astride

the seat. If a second passenger is board-
ing, have him or her follow the same pro-
cedure.

NOTE:

When a passenger is boarding, both the pas-
sengers and the operator should try to bal-
ance the watercraft.

(5) Check that the passengers have their

feet on the floor of the footwell and are
securely holding on to the person in front
of them or to the handgrip provided. Nev-

UF1K72E0.book Page 58 Wednesday, August 2, 2006 10:43 AM

«
...
63
64
65
66
67
...
»

Содержание WaveRunner VX Deluxe 2007

































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX Deluxe 2007

FLEXIBLE FURLER 2

Бренд: CDI Страницы: 18

Бренд: komodo Страницы: 12

Бренд: Grady-White Boats Страницы: 80

Бренд: Hunter Страницы: 161

XLT800 WaveRunner 2004

Бренд: Yamaha Страницы: 136

FT280 Fish Ranger

Бренд: Sevylor Страницы: 4

OMA-P5080-040401

Бренд: orangemarine Страницы: 16

Бренд: Sea-doo Страницы: 68

Бренд: Grady-White Boats Страницы: 80

Бренд: grabner Страницы: 28

380 express series

Бренд: Cruisers Yachts Страницы: 74

Бренд: Cruisers Yachts Страницы: 128

3580 Flybridge Series

Бренд: Cruisers Yachts Страницы: 130

Бренд: Sea Eagle Boats Страницы: 17

PT230 PONTOON THRUSTER

Бренд: Sideshift Страницы: 28

Бренд: Sideshift Страницы: 30

Бренд: RS SAILING Страницы: 43

Бренд: Silverton Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды