Yamaha WaveRunner VX Deluxe 2007 Скачать руководство пользователя страница 49

Страница: 49 / 96

Operation

EJU31890

Engine oil

Use a combination of the recommended SAE
and API engine oil classifications shown in the
chart below.

CAUTION:

ECJ00280

Use only 4-stroke engine oil.

EJU31930

Filling the fuel tank

CAUTION:

ECJ00290

Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.

(1) Remove the seat. (See page 26 for seat

removal and installation procedures.)

(2) Remove the fuel tank filler cap, and then

slowly add fuel to the fuel tank. Stop filling
when the fuel level reaches approximate-

ly 50 mm (2 in) from the top of the fuel
tank as indicated in the illustration.

(3) Install the fuel tank filler cap and the seat.

Approximately 50 mm (2 in) from top of the
fuel tank

Fuel tank capacity:

60 L (15.9 US gal) (13.2 Imp.gal)

UF1K72E0.book Page 42 Wednesday, August 2, 2006 10:43 AM

Содержание WaveRunner VX Deluxe 2007

































































































Результаты поиска

Содержание WaveRunner VX Deluxe 2007

Отзывы:

Похожие инструкции для WaveRunner VX Deluxe 2007

Бренды по названию

Популярные бренды

Yamaha WaveRunner VX Deluxe 2007, Руководство владельца/оператора

Результаты поиска

Содержание WaveRunner VX Deluxe 2007

Отзывы:

Похожие инструкции для WaveRunner VX Deluxe 2007

Бренды по названию

Популярные бренды