background image

Operation

52

(1) Launch the watercraft and start the en-

gine. (See page 52 for engine starting
procedures.)

(2) For the first 5 minutes, run the engine at

trolling speed only. For the 30 minutes of
operation after that, keep the engine
speed below 5000 r/min. For the 1 hour of
operation after that, keep the engine
speed below 6500 r/min.

(3) Proceed with normal operation.

CAUTION:

ECJ00430

Failure to follow the engine break-in pro-
cedure could result in reduced engine life
or even severe engine damage.

EJU32811

Launching the watercraft 

When launching the watercraft, make sure
that there are no obstacles around you.
If there are waves, someone should make
sure that the watercraft is not pushed into the
trailer after launching the watercraft.

For VX Deluxe/VX Cruiser:
Use the remote control transmitter to select
the unlock mode. (See page 32 for Yamaha
Security System and low-RPM mode selec-
tion procedures.)
After the watercraft is in the water, start the
engine. Shift into reverse and move the wa-
tercraft back slowly.

For VX:
After the watercraft is in the water, turn it
around so that the bow faces the direction
you wish to go. Start the engine, and then
slowly move away from the launching area.

EJU32850

Starting the engine 

WARNING

EWJ00560

Never start the engine or let it run for any
length of time in an enclosed area. Ex-
haust fumes contain carbon monoxide, a

colorless, odorless gas that may cause
loss of consciousness and death within a
short time. Always operate the watercraft
in an open area.

(1) If the lock mode of the Yamaha Security

System is selected (for VX Deluxe/VX
Cruiser), use the remote control transmit-
ter to select the unlock mode. (See page
32 for Yamaha Security System and low-
RPM mode selection procedures.)

(2) Launch the watercraft in water free from

weeds and debris and at least 60 cm (2 ft)
deep.

WARNING

EWJ00570

Never operate in water that is less than 60
cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged ob-
ject, which could result in injury.

CAUTION:

ECJ00470

Never operate in water that is less than 60
cm (2 ft) deep, otherwise pebbles or sand
could be sucked into the jet intake, caus-
ing impeller damage and engine overheat-
ing.

UF1K72E0.book  Page 52  Wednesday, August 2, 2006  10:43 AM

Содержание WaveRunner VX Deluxe 2007

































































































Отзывы: