Yamaha WaveRunner VX Cruiser 2007 страница 75 Скачать руководство пользователя | Manualshive

Страница: 75 / 96

background image

Maintenance and care

68

●

Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.

●

Stop the engine before refueling.

●

Refuel in a well-ventilated area with the
watercraft in a horizontal position.

●

Do not stand or sit on the watercraft
while refueling in case of fire.

●

Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.

●

Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level reaches approxi-
mately 50 mm (2 in) from the top of the
fuel tank. Fuel expands as it warms up
and could overflow if the fuel tank has
been overfilled. If temporarily leaving
the watercraft with a full fuel tank, do not
leave it in direct sunlight. Leave it in a
well-ventilated area with the watercraft
in a horizontal position.

●

Tighten the fuel tank filler cap securely
after refueling.

●

If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.

●

If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.

Top off the fuel tank with fresh gasoline and
add fuel stabilizer and conditioner to the fuel
tank according to the manufacturer’s instruc-
tions.

EJU33680

Battery

If the watercraft will not be used for more than
a month, remove the battery from the water-
craft and store it in a cool, dry place.

(1) Disconnect the negative (–) battery lead

first, then the positive (+) battery lead and
breather hose, and then remove the bat-
tery from the watercraft.

(2) Clean the battery casing using fresh wa-

ter.

(3) If the battery terminals are dirty or corrod-

ed, clean them with a wire brush.

(4) Fully charge the battery.
(5) Apply Yamaha Marine Grease or

Yamaha Grease A to the battery termi-
nals, and then store the battery in a cool,
dry place.

(6) Check the battery at least once every 2

months and fully charge it if necessary.

CAUTION:

ECJ00100

Always keep the battery charged. Storing
a discharged battery can cause permanent
battery damage.

To check the condition of the battery, check
the specific gravity of the electrolyte or mea-
sure the voltage at both battery terminals.
Charge the battery if the voltage is less than
12 volts.

It is recommended to have a Yamaha dealer
check the specific gravity and charge the bat-
tery. If you maintain the battery yourself, be
sure to read and follow the instructions provid-
ed with the battery tester and charger you
use.

EJU33730

Cleaning the watercraft

Clean the watercraft before storing it for a long
period.
(1) Wash down the hull, handlebars, and jet

unit with fresh water.

Specific gravity (for reference):

1.28 at 20 °C (68 °F)

UF1K72E0.book Page 68 Wednesday, August 2, 2006 10:43 AM

«
...
73
74
75
76
77
...
»

Содержание WaveRunner VX Cruiser 2007

































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX Cruiser 2007

Бренд: KL Outdoor Страницы: 8

Бренд: Robalo Страницы: 78

Бренд: Johnson Outdoors Страницы: 8

Бренд: Baja Страницы: 86

Бренд: M.E.S. Marine Страницы: 27

Бренд: elv Страницы: 40

Бренд: SeaDoo Страницы: 391

Бренд: Yamaha Страницы: 117

Бренд: Lagoon Страницы: 122

Бренд: Nauticstar Страницы: 80

Бренд: MACGREGOR Страницы: 28

Бренд: Sea Ray Страницы: 46

Бренд: Sea Ray Страницы: 44

Бренд: Sea Ray Страницы: 158

Бренд: Advanced Elements Страницы: 16

Бренд: Moomba Страницы: 84

Бренд: Highfield Страницы: 8

Бренд: Highfield Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды