Yamaha WaveRunner VX Cruiser 2007 страница 68 Скачать руководство пользователя | Manualshive

Страница: 68 / 96

background image

Operation

61

CAUTION:

ECJ00550

Do not operate the engine at full throttle
for at least 1 minute after the engine has
been restarted. Excessive water in the
bilge can splash into the engine, which
can result in severe damage.

NOTE:

To efficiently discharge water from the engine
compartment, operate the watercraft as
straight as possible and above planing speed
for at least 2 minutes.

EJU33250

Turning the watercraft

Steering control depends on the combination
of handlebar position and the amount of throt-
tle.
Water sucked in through the intake grate is
pressurized by the impeller in the jet pump. As
the pressurized water is expelled from the
pump through the jet thrust nozzle, it creates
thrust to move and steer the watercraft. The
higher the engine speed, the more thrust pro-
duced.
The amount of jet thrust, in addition to the po-
sition of the handlebars, determines how
sharply you turn.
A.

More throttle produces higher thrust, so
the watercraft will turn more sharply.

B.

Less throttle produces lower thrust, so
the watercraft will turn more gradually.

C. Releasing the throttle lever completely

produces only minimum thrust. If you are
traveling at speeds above trolling, you will
have rapidly decreasing ability to steer
without throttle. You may still have some
turning ability immediately after releasing
the throttle lever, but once the engine
slows down, the watercraft will no longer
respond to handlebar input until you ap-
ply throttle again or you reach trolling
speed.
At trolling speed, the watercraft can be
turned gradually by handlebar position
alone using just the amount of thrust
available at idle.

UF1K72E0.book Page 61 Wednesday, August 2, 2006 10:43 AM

«
...
66
67
68
69
70
...
»

Содержание WaveRunner VX Cruiser 2007

































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX Cruiser 2007

Бренд: Pakayak Страницы: 4

32 Express 2010

Бренд: Pro-Line Boats Страницы: 72

Бренд: Regal Страницы: 352

Бренд: Hobie Страницы: 16

Бренд: Supra Страницы: 92

Бренд: Supra Страницы: 88

Бренд: Axopar Страницы: 44

Бренд: Axopar Страницы: 68

Бренд: SEALINE Страницы: 95

Бренд: Grady-White Boats Страницы: 72

Бренд: Grady-White Boats Страницы: 74

Бренд: Grady-White Boats Страницы: 86

Бренд: Grady-White Boats Страницы: 112

Бренд: Sea-doo Страницы: 130

2014 Spark Series

Бренд: Sea-doo Страницы: 148

230 Challenger 2008

Бренд: Sea-doo Страницы: 160

Бренд: Hunter Страницы: 216

Бренд: Nortik Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды