Yamaha WaveRunner VX 2018 страница 89 Скачать руководство пользователя

Страница: 89 / 108

Care and storage

Checking the battery bands

Make sure that the battery bands are not
damaged.

To store the battery:
(1) Clean the battery case using fresh water.
(2) If the battery terminals are dirty or cor-

roded, clean them using a wire brush.

(3) Apply water-resistant grease to the bat-

tery terminals.

(4) Store the battery in a cool, dry place.

NOTICE:

Storing the battery in an un-

charged condition can cause perma-
nent battery damage. Check the
battery periodically.

[ECJ00103]

To install the battery:
(1) Place the battery in the battery compart-

ment and hook the battery bands onto
the holders.

(2) Connect the positive (+) battery lead (red)

to the positive (+) battery terminal.

NOTICE:

Reversal of the battery leads

will damage the electrical parts.

[ECJ00262]

(3) Connect the negative (–) battery lead

(black) to the negative (–) battery termi-
nal.

(4) Connect the breather hose to the bat-

tery.

WARNING! Fire or explosion

could result if the breather hose is
damaged, obstructed, or not connect-
ed properly.

[EWJ00452]

(5) Make sure that the battery is securely

held in place.

Battery band

Battery terminal

Recommended water-resistant grease:

YAMALUBE MARINE
GREASE/Yamaha Grease A

UF4G72E0.book Page 83 Tuesday, August 1, 2017 11:30 AM

Содержание WaveRunner VX 2018













































































































Результаты поиска

Содержание WaveRunner VX 2018

Отзывы:

Похожие инструкции для WaveRunner VX 2018

Бренды по названию

Популярные бренды

Yamaha WaveRunner VX 2018, Руководство владельца/оператора

Результаты поиска

Содержание WaveRunner VX 2018

Отзывы:

Похожие инструкции для WaveRunner VX 2018

Бренды по названию

Популярные бренды