Yamaha WaveRunner VX 2018 страница 59 Скачать руководство пользователя | Manualshive

Страница: 59 / 108

background image

Operation and handling requirements

53

EJU40291

Engine oil requirements

EJU43950

Engine oil

NOTICE

ECJ00282

Use only 4-stroke engine oil. Usage of 2-
stroke engine oil could result in severe en-
gine damage.

Checking the engine oil level

WARNING

EWJ00341

Engine oil is extremely hot immediately af-
ter the engine is turned off. Coming in con-
tact with or getting any engine oil on your
clothes could result in burns.

NOTICE

ECJ00392



Do not run the engine with too much or
not enough oil in the oil tank, otherwise
the engine could be damaged.



Make sure that debris and water do not
enter the oil tank filler hole. Debris and
water in the engine oil can cause serious
engine damage.

TIP:



When checking the engine oil level on land,
the engine must be running while water is
being supplied to the cooling water pas-
sages. (See “Flushing the cooling water
passages” on page 80 for information on
supplying water.)



When checking the engine oil level on wa-
ter, moor the watercraft so that it will not
drift away.

To check the engine oil level:
(1) With the engine stopped, place the wa-

tercraft in a precisely level position on
land or launch the watercraft.

(2) Look in all directions, and then start the

engine. (See page 69 for information on
starting the engine.)

(3) Run the engine at idling speed for 6 mi-

nutes or more. Run the engine an addi-
tional 5 minutes if the ambient
temperature is 20 °C (68 °F) or less.

(4) Stop the engine.
(5) Remove the seats. (See page 43 for seat

removal and installation procedures.)

(6) Loosen the oil tank filler cap and remove

it, and then wipe the attached dipstick
clean.

(7) Screw the oil tank filler cap into the filler

hole until it stops. Remove the oil tank
filler cap again and make sure that the

Recommended engine oil type:

SAE 10W-30, 10W-40, 20W-40,
20W-50

Recommended engine oil grade:

API SG, SH, SJ, SL

1

Oil tank filler cap/Dipstick

1

UF4G72E0.book Page 53 Tuesday, August 1, 2017 11:30 AM

«
...
57
58
59
60
61
...
»

Содержание WaveRunner VX 2018













































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX 2018

Бренд: Malibukayaks Страницы: 19

Sport Boat Models

Бренд: LARSON Страницы: 102

1992 270 Weekender

Бренд: Sea Ray Страницы: 21

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 32

Бренд: Yamaha Страницы: 84

SX230 High output

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 113

Бренд: Yamaha Страницы: 128

SUV1200 WaveRunner 2004

Бренд: Yamaha Страницы: 140

SUV1200 WaveRunner 2003

Бренд: Yamaha Страницы: 140

GP800R WaveRunner 2003

Бренд: Yamaha Страницы: 124

FX Cruiser WaveRunner 2007

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 121

GP1300R WaveRunner 2003

Бренд: Yamaha Страницы: 126

GP1200R WaveRunner 2001

Бренд: Yamaha Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды