Yamaha WaveRunner VX 2018 страница 101 Скачать руководство пользователя | Manualshive

Страница: 101 / 108

background image

Trouble recovery

95

ler, jet pump housing, and jet thrust noz-
zle.
If debris is difficult to remove, consult a
Yamaha dealer.

EJU43472

Raising the reverse gate

If the RiDE system malfunctions and the re-
verse gate remains in the lowered position,
the watercraft will not be able to move for-
ward.
After raising the reverse gate so that the wa-
tercraft can move forward, immediately re-
turn to shore and have a Yamaha dealer
service the watercraft.
To raise the reverse gate:
(1) Stop the engine and remove the clip from

the engine shut-off switch.

(2) Enter the water and move to the rear of

the watercraft.

(3) Slide the shift rod joint toward the bow,

and then disconnect the shift rod joint
from the ball joint.

(4) Raise the reverse gate to the forward po-

sition.

TIP:



While the shift rod is disconnected, the re-
verse gate will not move to the neutral po-
sition or reverse position even if the RiDE
lever is squeezed.



If the RiDE lever is squeezed while the shift
rod is disconnected, the watercraft will
move forward.

EJU34642

Jumping the battery

If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.

EJU34664

Connecting the jumper cables

WARNING

EWJ01251

To avoid battery explosion and serious
damage to the electrical system:



Do not reverse the polarity of the jumper
cables when connecting to the batter-
ies.



Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.



Do not touch the positive (+) jumper ca-
ble to the negative (–) jumper cable.

1

Shift rod joint

2

Ball joint

1

2

1

Reverse gate

2

Forward position

1

2

UF4G72E0.book Page 95 Tuesday, August 1, 2017 11:30 AM

«
...
99
100
101
102
103
...
»

Содержание WaveRunner VX 2018













































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VX 2018

Cross 75 Bow Rider

Бренд: YAMARIN Страницы: 42

Бренд: NorthStar Страницы: 56

R-29 Command Bridge

Бренд: Ranger Tugs Страницы: 21

Бренд: Solo Skif Страницы: 9

Бренд: Scout Boats Страницы: 116

Бренд: Ranger Страницы: 78

Бренд: J Страницы: 52

Бренд: Hunter Страницы: 157

Бренд: Palfinger Страницы: 259

Бренд: Gumotex Страницы: 52

Grand Soleil 40

Бренд: Cantiere Del Pardo Страницы: 97

Бренд: Bavaria Страницы: 85

Бренд: Gumotex Страницы: 52

Бренд: Bayliner Страницы: 96

MilPro ERB 310 HPP

Бренд: Zodiac Страницы: 28

Бренд: Zodiac Страницы: 35

GLACEIR BAY EDITION 2770

Бренд: WORLDCAT Страницы: 100

Бренд: Topaz Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды