background image

 

28

 

Instruments and indicators

 

EMU26493

 

Digital tachometer

 

The tachometer shows the engine speed
and has the following functions.
All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

TIP:

 

The water separator and engine trouble-alert
indicators only operate when the engine is
equipped with the appropriate functions.

 

EMU36050

 

Tachometer

 

The tachometer displays engine speed in
hundreds of revolutions per minute (r/min).
For example, if the tachometer display reads
“22” then the engine speed is 2200 r/min.

 

EMU26621

 

Trim meter

 

This meter shows the trim angle of your out-
board motor.

 

 

Memorize the trim angles that work best
for your boat under different conditions.
Adjust the trim angle to the desired using

the power trim and tilt switch.

 

 

If the trim angle of your motor exceeds the
trim operating range, the top segment on
the trim meter display will blink.

 

EMU26651

 

Hour meter

 

This meter shows the number of hours the
engine has been run. It can be set to show
the total number of hours or the number of
hours for the current trip. The display can
also be turned on and off.

To change the display format, press the

” (mode) button. The display can show

total hours or trip hours, or turn off.
To reset the trip hours, simultaneously press
the “

” (set) and “

” (mode) buttons for

more than 1 second while the trip hours are
displayed. This resets the trip counter to 0
(zero).
The total number of hours the engine has
been run cannot be reset.

 

1. Tachometer
2. Trim meter
3. Hour meter
4. Oil level indicator
5. Overheat-alert indicator
6. Set button
7. Mode button

1

3

5

6

7

4

2

ZMU01891

ZMU01869

ZMU01870

Содержание VZ200R

































































































Отзывы: