manualshive.com logo in svg

Yamaha VX150A, Руководство пользователя

Поделиться
Скачать
Yamaha VX150A Скачать руководство пользователя страница 63

E

3-22

UP
DN

701034**

UP

DN

403033

302012

UP

DOWN

EMU01201

PROCEDURE FOR TILTING UP

Power trim/tilt model

1)

If there is a fuel joint or a fuel cock on
the boat, disconnect the fuel line or
close the fuel cock.

2)

Push the power trim/tilt switch “UP”
until the outboard has tilted up com-
pletely.

3)

Turn the tilt-support lever toward you
and support the engine.

w

After tilting the engine, be sure to sup-
port it with the tilt-support lever.
Otherwise, the engine could fall back
down suddenly if oil in the power
trim/tilt unit should lose pressure.

4)

Once the engine is supported with the
tilt-support lever, push the power
trim/tilt switch DOWN to retract the
trim rods.

c

C

Be sure to retract the trim rods complete-
ly during mooring. This protects the rods
from marine growths and corrosion
which could damage the power trim/tilt
mechanism.

Содержание VX150A























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды