Yamaha VX150A Скачать руководство пользователя | Manualshive

Страница: 102 / 118

background image

E

5-7

ON

START

OFF

701026

301021

208036

301022

EMU00430

Emergency Starting Engine

1)

Remove the top cowling.

2)

Remove the flywheel cover.

3)

Prepare the engine for starting. See
“STARTING ENGINE” for procedures.
Be sure the engine is in Neutral and
that the lanyard is attached to the
engine stop switch.

4)

Turn the main switch to START and
back to OFF several times to inject
some fuel into the combustion cham-
bers, then put the switch in the ON
position.

5)

Insert the knotted end of the emer-
gency starter rope into the notch in
the flywheel rotor and wind the rope
several turns clockwise.

6)

Give a strong pull straight out to
crank the engine. Repeat if necessary.

NOTE:

If the engine will not start with this proce-
dure, refer to “ENGINE FAILS TO OPER-
ATE”.

«
...
100
101
102
103
104
...
»

Содержание VX150A























































































































Отзывы:

Нет отзывов

Похожие инструкции для VX150A

Бренд: ECS Страницы: 64

Бренд: IBASE Technology Страницы: 91

Бренд: ASROCK Страницы: 212

VVDI Mini Key Tool

Бренд: Xhorse Страницы: 17

Бренд: HONDA marine Страницы: 2

Бренд: Abit Страницы: 110

Бренд: Fastrax Страницы: 12

NOVA-PV-D5251-G4-R11

Бренд: IEI Technology Страницы: 18

Бренд: AXIOMTEK Страницы: 72

Бренд: TYAN Страницы: 59

Бренд: MSI Страницы: 108

Бренд: JGINYUE Страницы: 14

Бренд: Texas Instruments Страницы: 14

Бренд: Gigabyte Страницы: 36

Бренд: u-blox Страницы: 48

Бренд: Yamaha Страницы: 12

Бренд: Yamaha Страницы: 392

Бренд: Gigabyte Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды