manualshive.com logo in svg

Yamaha VX150A, Руководство пользователя

Поделиться
Скачать
Yamaha VX150A Скачать руководство пользователя страница 31

E

2-10

802016*

TRIP

TIME

BATT

Km/h

knot

mph

km

mile

SPEED

YAMAHA

set

mode

q

w

e

r

001052

q

EMU01553

Overheat Warning Indicator

If the engine temperature rises too high,
the warning indicator will start to blink.
Refer to “OVERHEAT WARNING” for
details.

1

Overheat warning indicator

c

C

Do not continue to operate the engine if a
warning device has activated. If neces-
sary, refer to the “TROUBLESHOOTING”
section in this manual. Consult your deal-
er if the problem cannot be located and
corrected.

EMU00140

DIGITAL SPEEDOMETER

This meter contains the speedometer, fuel
meter with warning, trip meter, clock and
voltmeter with warning.

1

Speedometer

2

Fuel meter

3

Trip meter/clock/voltmeter

4

Warning indicator

NOTE:

After the main switch is first turned on, all
portions of the meter come on as a check.
After a few seconds, the meters will
change to normal operation. Watch the
meter when turning on the main switch to
make sure all segments come on.

802034

TRIP

TIME

BATT

Km/h

knot

mph

km

mile

SPEED

YAMAHA

set

mode

Содержание VX150A























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды