Yamaha VX Sport Скачать руководство пользователя

Страница: 85 / 106

Care and storage

Checking the battery bands

Make sure that the battery bands are not
damaged.

To store the battery:
(1) Clean the battery case using fresh water.
(2) If the battery terminals are dirty or corrod-

ed, clean them using a wire brush.

(3) Apply YAMALUBE MARINE GREASE to

the battery terminals.

(4) Store the battery in a cool, dry place.

NOTICE:

Storing the battery in an un-

charged condition can cause perma-
nent battery damage. Check the
battery periodically.

[ECJ00102]

To install the battery:
(1) Place the battery in the battery compart-

ment and hook the battery bands onto the
holders.

(2) Connect the positive (+) battery lead (red)

to the positive (+) battery terminal.

NOTICE:

Reversal of the battery leads

will damage the electrical parts.

[ECJ00261]

(3) Connect the negative (–) battery lead

(black) to the negative (–) battery termi-
nal.

(4) Connect the breather hose to the battery.

WARNING! Fire or explosion could re-
sult if the breather hose is damaged,
obstructed, or not connected proper-
ly.

[EWJ00451]

(5) Make sure that the battery is securely

held in place.

Battery band

Battery terminal

Recommended water-resistant grease:

YAMALUBE MARINE GREASE

chapter12 Page 80 Wednesday, October 14, 2009 3:07 PM

Содержание VX Sport











































































































Результаты поиска

Содержание VX Sport

Отзывы:

Похожие инструкции для VX Sport

Бренды по названию

Популярные бренды

Yamaha VX Sport, Руководство пользователя

Результаты поиска

Содержание VX Sport

Отзывы:

Похожие инструкции для VX Sport

Бренды по названию

Популярные бренды