Yamaha VX Sport Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 106

Yamaha VX Sport Скачать руководство пользователя страница 76

Operation

71

run the engine in water that is less than 60
cm (2 ft) deep from the bottom of the wa-
tercraft, otherwise pebbles or sand could
be sucked into the jet intake, causing im-
peller damage and engine overheating.

[ECJ00472]

TIP:

VX Cruiser: This watercraft is equipped with a
reboarding step, which can be lowered and
used to assist in reboarding. (See page 45 for
information on operating the reboarding step.)

EJU36353

Boarding alone

(1) From the rear of the watercraft, place

both hands on the boarding platform, pull
yourself up, and then grasp the handgrip
with one hand.

(2) Pull yourself up to a kneeling position on

the boarding platform, and then move to
the seat and sit astride.

(3) Attach the engine shut-off cord (lanyard)

to your left wrist, and then attach the clip
to the engine shut-off switch.

(4) Grip the handlebars with both hands and

place both feet on the floor of the footwell.

(5) Look in all directions, start the engine,

and then start off slowly.

EJU33169

Boarding with passenger(s)

WARNING

EWJ00660

Severe internal injuries can occur if water
is forced into body cavities as a result of
being near the jet thrust nozzle. Do not ap-
ply throttle until the passengers are seated
with their feet on the floor of the footwell
and are securely holding on to the person

60 cm (2 ft)

UF2N10E0.book Page 71 Tuesday, October 6, 2009 5:02 PM

«
...
74
75
76
77
78
...
»

Содержание VX Sport











































































































Отзывы:

Нет отзывов