Yamaha VX Sport Скачать руководство пользователя | Manualshive

Страница: 83 / 106

background image

Care and storage

78

flows out continually from the jet thrust
nozzle.

(7) Run the engine at idling speed for about

3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and perform
the procedure again from step 6.

NOTICE:

Do not supply water to the

cooling water passages when the en-
gine is not running. The water could
flow back through the muffler into the
engine, causing severe engine dam-
age.

[ECJ00122]

(8) Turn the water supply off.
(9) Discharge the remaining water out of the

cooling water passages by alternately
squeezing and releasing the throttle lever
quickly for 10 to 15 seconds.

(10) Stop the engine.
(11) Remove the garden hose adapter, and

then securely install the flushing hose
connector cap by tightening it until it
stops.

(12) Securely install the seat in its original po-

sition.

EJU41690

Cleaning the watercraft

(1) Remove the seat. (See page 44 for seat

removal and installation procedures.)

(2) If the watercraft will be stored for a week

or more, rustproof the internal engine
components to help prevent corrosion.

(See page 82 for information on rust-
proofing the internal engine compo-
nents.)

(3) Rinse the engine and engine compart-

ment with a small amount of water.

NOTICE:

Do not use high-pressure

water when rinsing the engine or en-
gine compartment as severe engine
damage could result.

[ECJ00571]

(4) Drain the water from the engine compart-

ment. (See page 53 for information on
draining the bilge water.)

(5) Wipe the engine and engine compart-

ment with a dry cloth.

(6) Wash down the hull, deck, and jet pump

with fresh water.

(7) Wipe the hull, deck, and jet pump with a

dry cloth.

(8) Wipe all vinyl and rubber components,

such as the seat and engine compart-
ment seals, with a vinyl protectant such
as Yamaha Protectant.

(9) To minimize corrosion, spray metallic

parts of the hull, deck, and engine with a
rust inhibitor such as Yamaha Silicone
Protectant and Lubricant.

(10) Allow the engine compartment to air dry

completely before installing the seat.

(11) Securely install the seat in its original po-

sition.

EJU41630

Battery care

If the watercraft will not be used for more than
a month, remove the battery from the water-
craft, check it, and then store it in a cool, dry
place.

WARNING

EWJ00791

Battery electrolyte is poisonous and dan-
gerous, causing severe burns, etc. Elec-
trolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.

chapter12 Page 78 Wednesday, October 14, 2009 3:07 PM

«
...
81
82
83
84
85
...
»

Содержание VX Sport











































































































Отзывы:

Нет отзывов

Похожие инструкции для VX Sport

Бренд: Zodiac Страницы: 31

Classic Runabout EP RTR

Бренд: ProBoat Страницы: 4

Musto Performance Skiff

Бренд: Bennett Страницы: 19

Бренд: Regal Страницы: 352

Бренд: NorthStar Страницы: 2

Бренд: NorthStar Страницы: 2

Бренд: Boston Whaler Страницы: 98

Бренд: Sea-doo Страницы: 24

Бренд: Sea-doo Страницы: 123

Бренд: Sea-doo Страницы: 100

Бренд: Sea-doo Страницы: 109

303 Single Seater

Бренд: Access Dinghy Sailing Страницы: 12

Бренд: Hunter Страницы: 23

Бренд: World Cat Страницы: 99

Бренд: Yamaha Страницы: 515

Бренд: Yamaha Страницы: 164

Бренд: Marine Concepts Страницы: 7

Бренд: Topper Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды